Bandit
13
MODEL SG-40
CONTROLS
Refertoenginemanufacturer’smanualforspecific
engine controls and operation.
CONTROLS
1. A. Cutter Wheel Up/Down:
Tomovethecutterwheelup;pullthejoystickonthevalvebanktowardsthebackof
themachine.Tomovethecutterwheeldown;pushthejoystickonthevalvebanktowardsthefrontofthemachine.
B. Swing Left/Right:
Tomovethecutterwheeltotheleft;pushthejoystickonthevalvebanktowards
theleftsideofthemachine.Tomovethecutterwheeltotheright;pushthejoystickonthevalvebank
towards the right side of the machine.
2. Left Track Forward/Reverse:
Tomovethelefttrackforward;pushthehandleonthevalvebanklabelled
“L.TrackForward”towardsthefrontofthemachine.Toreversethelefttrack;pullthehandleonthevalve
bank labelled “L. Track Reverse” towards the back of the machine.
3. Right Track Forward/Reverse:
Tomovetherighttrackforward;pushthehandleonthevalvebank
labelled“R.TrackForward”towardsthefrontofthemachine.Toreversetherighttrack;pullthehandle
on the valve bank labelled “R. Track Reverse” towards the back of the machine.
4. Emergency Stop Button:
When the emergency stop button is pressed the entire machine will shut down.
The cutter wheel will not stop immediately stop, it will coast to a stop.
5.
Cutter Wheel On/Off Switch:
Before turning the cutter wheel on, make sure the engine is at low idle.
Flip the switch to the “On” position, then throttle the machine up.
6. Swing Out Console Lock:
To change the swing out position, pull the swing out console lock handle
towards the back of the machine and move the console swing arm to the left or right side, and release
the handle. Continue to move the console swing arm until it locks into place.
7. Tach/Hour Meter:
The tach/hour meter keeps track of the amount of hours on the machine.
8. Swing Speed Control:
To control the swing speed so the swing speed is increased, loosen the swing
speed valve. To control the swing speed so the swing speed in decreased, tighten the swing speed valve.
9. Ignition Switch:
To start the machine, insert the ignition key, and turn towards the front of the machine.
Toturnthemachineoff,turnthekeytothebackofthemachine,andremovethekey.
10. Throttle Up/Down Lever:
To throttle the machine up move the lever to the high RPM symbol. To throttle
the machine down move the low RPM symbol.
NOTICE
Summary of Contents for SG-40
