background image

16 / 25

23526b GB/2019-07

1

 electronic GmbH & Co. KG  •  Heinrichstraße 3-4  •  12207 Berlin  •  Deutschland  •  [email protected]

4.2  

General use  

Step 1: 

Check cable connections

  Verify that all connecting cables and couplings are correctly connected.

Step 2: 

Prepare the sonication

To do so, see the corresponding user instructions for tank baths, ultrasonic transducer 
systems, or reactors.

  Prepare the sonicating medium and check that the 

fi

 ll level is correct.

Step 3: 

Start ultrasound operation

  Press the mains switch. 

The fan on the rear of the generator turns on. 
When the power is switched on, all LEDs light up for approx. 4 seconds at the HF 
unit. The "TEMPERATURE" LED 

fl

 ashes during this time. 

  Turn on the HF unit with the "ACTIVE" switch.

  After a few seconds, when the power has been achieved, the "CONTROL" LED 

(green) for the working HF units will be lit up. 
If "CONTROL" is not triggered or if "TRANSDUCER" or "DRY" light up, there is 
an error or incorrect adjustment (see chapter 6.2). 

Step 4: 

Stop ultrasound operation

  In order to stop the power output, press the "ACTIVE" switch. 

  To turn the generator off, press the mains switch on the rear.

For additional care instructions, see chapter 5.

Summary of Contents for SONOREX TECHNIK TG Series


























Reviews: