background image

 

1

2

3

1 = HF "+"
2 = HF "-"
3 = PE

Label:

1500 W

25 kHz

12 / 25

23526b GB/2019-07

1

 electronic GmbH & Co. KG  •  Heinrichstraße 3-4  •  12207 Berlin  •  Deutschland  •  [email protected]

•  Hang the generator in a dust-free, dry position. 

A minimum distance of 10 cm in all directions is required for suf

fi

 cient cooling 

  Installation in an enclosed construction is not permitted.

•  Drill holes for the screws (e.g. M5) leaving 255 mm between them and paying 

attention to suf

fi

 cient height.

•  Attach the bracket on the left or right using the screws in the housing as shown 

in the 

fi

 gure.

•  Mount the generator.

2.2.2  HF connection for ultrasonic transducer  

One or more ultrasonic transducers with a maximum total output of 1,500 W can be 
connected to a generator (cleaning baths, immersible transducers, 

fl

 at transducer 

plates, reactors, etc.) The minimum connected output of 300 W per HF unit must be 
upheld.

Correct connection of the HF unit(s) with the load:

The factory-set data for the HF unit is af

fi

 xed next 

to the HF connection socket.

HF output socket:

  Connect the installed ultrasonic transducers (cleaning tanks (TM), immersible 

transducers, 

fl

 at transducer plates, reactors, etc.) to the respective HF units 

on the rear of the generator using the HF cable (maximum length of 
HF feed cable: 20 m). 
The correct assignment of the load to the HF unit (frequency and maximum output) 
must be taken into account under all circumstances!

The 3-pole plug should be connected to the generator as follows:
-  Align and insert the plug (without rubber bushing) and socket (red dot at top, on 

both sides) into one another until the connection clicks into place! 
If the plug is not correctly plugged in and locked in place, this can lead to failure 
of the connection (scorching) or the generator.

-  In order to join multiple ultrasonic transducers for connection to an HF unit, 

the appropriate TV 2 or TV 4 junction boxes with HF feed cables must be 
available or ordered.

HF cables with plug connectors should be protected against splash water or moisture 
(protection class: IP 51).

Summary of Contents for SONOREX TECHNIK TG Series


























Reviews: