background image

BEFORE INSTALLATION

8

IMPORTANT SAFETY INSTRUCTIONS FOR

INSTALLATION

Warning: Incorrect installation can lead to severe injury.
Follow ALL installation instructions.

SIDE ROOM REQUIREMENTS

Fig. 1

shows the minimum side room that is required. The

distance between the edge of the door curtain and the inside of

the bracket is 85mm minimum, and the distance between the

edge of the door curtain and the outside of the bracket is

135mm minimum.

Fig. 2

shows the recommended side room. The distance

between the edge of the door curtain and the inside of the

bracket should be 110mm , and the distance between the edge

of the door curtain and the outside of the bracket is 160mm.

1. CHECK OPERATION OF DOOR

BEFORE BEGINNING THE INSTALLATION OF THE

EASYLIFTER AUTOMATIC GARAGE DOOR OPENER CHECK THE

OPERATION OF THE DOOR.

The door must be well balanced and be in a reasonable

operating condition. You should be able to lift the door

smoothly and with little resistance. It should stay open around

900mm to 1200mm above the

r. The door should not stick

or bind in the guide tracks. The ideal operational e ort in

raising or lowering the door should not exceed a force of 10kg

(22 lbs.). Make sure that all door locks are either removed, or

disabled and remove unnecessary accessories.

2.  FIXING OF DOOR WEIGHT BARS

Move the door manually to the mid open position. Place the

weight bars equally apart on the bottom rail of the door and

secure them with the fasteners provided

  (Fig. 3)

. Check the

operation of the door again. If the door feels heavy it may

require extra tension to be added to the door springs. Refer to

the door Installation manual from the manufacturer on how to

tension the door.

3. LEFT OR RIGHT HAND INSTALLATION

FIG. 3

FIG. 2

FIG. 1

MINIMUM SIDE ROOM

RECOMMENDED SIDE ROOM

FIG. 4

FIG. 5

Connect the middle and left

hand side pins for left

hand side installation.

Connect the middle and

right hand side pins for

right hand side installation.

WEIGHT BARS

The Easylifter Automatic Garage Door Opener can be installed 
on the left or right hand side of the door (when looking out 
from the inside of the garage).  If the opener is to be installed on 
the RIGHT HAND side of the door, then no change needs to be 
made, as this is the standard factory setup.  If LEFT HAND side 
installation is required, the next step is to move the motor wire 
connector on the control board.  The connector plug has to be 
removed and reconnected to the LEFT side of the connector 
(Fig.4).  If you have made an error in the selection and wish to
install on the RIGHT HAND side, then reconnect the connector
plug on the RIGHT side of the connector (Fig.5)

Summary of Contents for Easylifter

























Reviews: