background image

TROUBLE SHOOTING

18

*Please Note: Some areas may be prone to excessive radio interference brought on by devices such as cordless telephones, wireless
stereo headphones and baby monitors. It is possible that these devices could cause a degree of interference such as to greatly reduce
the range of the transmitter. In such an instance please contact your B&D dealer for an alternative frequency replacement kit. As this is
not a warrantable situation but an environmental issue charges may apply for the changeover.

SYMPTOM

POSSIBLE CAUSE

REMEDY

Door will not operate.

Mains power not switched on.
Door is obstructed.
Door is locked or motor jammed.
Door tracks/hardware damaged.

Switch on mains power.
Remove obstruction.
Unlock door or remove jam.
Door requires service/repair by qualified

technician.

Door starts to close but automatically
reverses to open position.

Adverse weather conditions (wind or cold)
causing door to stiffen and become tight in
the tracks.
Possible obstruction in the doorway.

Increase  force  margin  setting  and/or  re-
initialise the door . See Step 8 on page 11.

Remove obstruction.

Door operates from drive unit (O/S/C)
button but not from transmitter.*
See note.

Transmitter code not stored in memory.

Flat Battery.

Code transmitter in to openers memory.

Refer Step 8.1 on page 14.
Replace battery - A23 Alkaline 12V.

Door will not close fully.

Door limit positions need to be reset.

Reset limit positions. See Step 6 Page 10.

Door will not open fully.

Door limit positions need to be reset.

Reset limit positions. See Step 6 Page 10.

Courtesy light not working.

Globe blown.

Replace globe - festoon type 15W 24V DC.

Globe keeps blowing.

Incorrect globe voltage - must be 24V DC. Replace globe - festoon type 15W 24V DC.

Auto close not working.

PE Beam or wiring faulty
PE Beam not aligned correctly.
PE Beam is obstructed.
Door obstructed when closing.
Auto close time not set.

Repair PE Beam or replace wiring.
Re-align optics.
Remove obstruction from the path of PE.
Remove obstruction.
See Step 15 on page 16.

DATE

MAINTENANCE PERFORMED BY

SIGNATURE

  AMOUNT INV. No.

Please Note: Failure to maintain your garage door may void the warranty for your garage door opener.

Summary of Contents for Easylifter

























Reviews: