manualshive.com logo in svg

BALZER Field Floater, Assembly Instructions Manual

Share
Download
BALZER Field Floater Assembly Instructions Manual Download Page 67

 67 

Temperature Range 

Oil Viscosity 

20-40⁰ F 

SAE 20 

40-100⁰ F 

SAE 30 

100-120⁰ F 

SAE 40 

120-140⁰ F 

SAE 50 

Oiler Viscosity Chart 

Pre-Startup 

Lubrication 

Fill oiler reservoir with chain oil. See Oiler Viscosity Chart below. Remove shields P# 91332 and P# 
41704. If grain cart is equipped with the joystick controller, press trigger for auger clutch and check for 
oil flow at the brushes. If grain cart is not equipped with the joystick controller, engage tractor control 
for auger clutch and check for oil flow at the brushes. Wait two to three seconds and repeat until oil flow 
is present. 

Automatic Chain Oiler 

Remove Shields 

P# 41704 

P# 91332 

The following procedure refers only to initial setup of the Field Floater IV Grain Cart. Refer to 
Lubrication and Maintenance section of the Field Floater IV Grain Cart manual for normal maintenance 
operations.  

The following components must be lubricated to avoid damage to 
the grain cart. 

CAUTION 

Summary of Contents for Field Floater












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands