Main Screen
SET FILTER CYCLE TIMES
SEQUENCE
TP200
USER GUIDE
42369 Rev A2
8
7
Balboa Water Group | Your Single Source Solution
Press the TEMP button. The
Set Temperature will appear
and flash.
While the Set Temperature is
flashing, press LIGHT until
F1 appears. F1 is an abbreviation
for “Filter Cycle 1”.
Press TEMP. The following
message means you are about
to set the start time of
Filter Cycle 1.
Press TEMP to view the
current start time. In this
example, the start time
is 7:00 PM.
Press TEMP change the hour
from 7 to 8.
Press LIGHT to select
the minutes.
Press TEMP to change the
minutes from 45 to 00.
Press LIGHT to save your
setting. The following message
means you are about to set the
duration. The same sequence
is used to set the start time and
the duration.
This message means Filter
Cycle 1 will end at 11:00 PM.
Press LIGHT to go back to the
Main Screen, or wait a few
moments and the Main Screen
will appear automatically.
Main Filtration
Filter cycles are set using a start time and
a duration. Hours are adjusted in 1-hour
increments, and minutes are adjusted in
15-minute increments. The end time is
calculated and displayed automatically.
Filter Cycle 1
In this example, we will do the following:
• View the current start time
• View the duration
• Set the start time to 8:00 PM
• Set the duration to 3 hours
This means Filter Cycle 1 will end at 11:00
PM. Follow the same sequence to set
Filter Cycle 1 for your spa.
View the next page to set the start time
and duration for Filter Cycle 2.
Flashing characters
Progressive message
Press TEMP button for “action”
Press LIGHT button to “select”
Pause / back to Main Screen / setting not saved
Pause / back to Main Screen / setting saved
Menu Items may or may not appear
SEQUENCE KEY
( View page 2 for full description )
Filter Cycle 2
In this example, we will do the following:
• Turn On Filter Cycle 2
• View the current start time
• View the duration
• Set the start time to 8:00 AM
• Set the duration to 3 hours
This means Filter Cycle 2 will end at 11:00
AM. Follow the same sequence to set
Filter Cycle 2 on your spa.
Filter Cycle 2 is optional. It is Off by
default on most control systems.
However, you can turn it On if you like.
It is possible to overlap Filter Cycle 1 and
Filter Cycle 2, which will shorten overall
filtration by the overlap amount.
Purge Cycles
The heater pump (view page 18) runs for
the whole duration of the filter cycle.
In order to maintain sanitary conditions,
secondary Pumps and/or a Blower
will purge water from their respective
plumbing by running briefly at the
beginning of each filter cycle.
If Filter Cycle 1 is set for 24 hours,
enabling Filter Cycle 2 will initiate a
purge when Filter Cycle 2 is programmed
to begin.
On some systems, purge cycles may run
several times a day, independent of the
filter cycle.
SET FILTER CYCLE TIMES
Press the TEMP button. The
Set Temperature will appear
and flash.
While the Set Temperature is
flashing, press LIGHT until
F2 appears.
Press TEMP. The following
message means Filter Cycle 2
is Off.
Press TEMP to turn On
Filter Cycle 2.
Press TEMP. The following
message means you are about
to set the start time of
Filter Cycle 2.
Press TEMP to view the
current start time.
Press TEMP change the hour
from 7 to 8.
Press LIGHT to select
the minutes.
Press TEMP to change the
minutes from 45 to 00.
Press LIGHT. The following
message means you are about
to set the duration. Use the
same sequence to set the start
time and duration.
This message means Filter
Cycle 2 will end at 11:00 AM.
Press the LIGHT button, and
the Main Screen will appear.
Or, pause a moment, and
the Main Screen will appear
automatically.
Main Screen
SEQUENCE
