manualshive.com logo in svg

Balboa TP200 PANEL, User Manual

Share
Download
Balboa TP200 PANEL User Manual Download Page 20

TP200 

USER GUIDE   

     

42369 Rev A2

36

35

Balboa Water Group   |   Your Single Source Solution

 PANEL MESSAGES

REMINDER

GFCI Failure - System Could Not Test/Trip the GFCI. 

NORTH AMERICA ONLY.  May indicate an unsafe installation. 
Contact your dealer or service organization.

Message
Code *

A Pump Appears to be Stuck ON. 

Water may be overheated. 
POWER DOWN THE SPA. DO NOT ENTER THE WATER.
Contact your dealer or service organization.

Message
Code *

A Pump Appears to have been Stuck ON when spa  
was last powered. 

POWER DOWN THE SPA. DO NOT ENTER THE WATER. 
Contact your dealer or service organization.

Message Code *

*

* *

View page 55 for instructions on how to review the Fault Log that corresponds with the Message Code.
This message can be reset from the panel with any button press.

Check pH 

This message may appear every 7 days. Check 
the pH of your spa’s water with a pH test kit, 
and adjust pH with the appropriate chemicals.

General maintenance 
helps your spa.

Reminder messages alternate with the  
Main Screen. 

Reminder Messages can be chosen 
individually by the Manufacturer. They may 
be disabled entirely, or there may be a limited  
number of Reminders on a specific model. 

The frequency of each Reminder (i.e. 7 days) 
can be specified by the Manufacturer. 

Press a Temperature button to reset a 
displayed Reminder Message.

The display of Reminder Messages can be 
turned On/Off (view page 43).

Check the sanitizer chemicals 

This message may appear every 7 days.  
Check sanitizer level and other water 
chemistry with a test kit and adjust with the 
appropriate chemicals.

Clean the water filter. 

This message may appear every 30 days. 
Clean the filter media as instructed by the 
manufacturer. See Hold Mode on page 14.

Main Screen

The water level is too low. 

Some systems have a water level detector, and this message 
appears if it detects that the water level is too low. Pumps are 
shut down until this problem clears.

Summary of Contents for TP200 PANEL


































Reviews:

No comments

Brands by name

Popular brands

Load more brands