background image

P/N 40632-99_D   02/12/2008

Warning! Shock Hazard! No User Serviceable Parts.

Do not attempt service of this control system. Contact your dealer or service organization for assistance. Follow 
all owner’s manual power connection instructions. Installation must be performed by a licensed electrician and all 
grounding connections must be properly installed.

Basic Installation and Configuration Guidelines for Mach 3 
EL-Series Spa Controllers.

Use minimum 6AWG copper conductors only.

Torque field connections between 21 and 23 in lbs.

Readily accessible disconnecting means to be provided at 
time of installation.

Permanently connected.

Connect only to a circuit protected by a Class A Ground Fault 
Circuit Interrupter (GFCI) mounted at least 5’ (1.52M) from the 
inside walls of the spa/hot tub and in line of sight from the 
equipment compartment.

CSA enclosure: Type 2

Typical field connections 
for main power.

Refer to Wiring Diagram 
inside the cover of the 
control enclosure.

Refer to Installation and 
Safety Instructions provided 
by the spa manufacturer.

Warning:

 

People with infectious diseases should not use a 

spa or hot tub.

Warning:

 

To avoid injury, exercise care when entering or 

exiting the spa or hot tub.

Warning:

 

Do not use a spa or hot tub immediately following 

strenuous exercise

Warning:

 

Prolonged immersion in a spa or hot tub may be 

injurious to your health

Caution:

 

Maintain water chemistry in accordance with the 

Manufacturers instructions.

Caution:

 

The equipment and controls shall be located not 

less than 1.5 meters horizontally from the spa or hot tub.

 

CSA Compliance/Conformité
Caution:

s4ESTTHEGROUNDFAULTCIRCUITINTERRUPTERBEFOREEACHUSEOF

the spa.

s2EADTHEINSTRUCTIONMANUAL
s!DEQUATEDRAINAGEMUSTBEPROVIDEDIFTHEEQUIPMENTISTO

be installed in a pit.

s&ORUSEONLYWITHINANENCLOSURERATED#3!%NCLOSURE
s#ONNECTONLYTOACIRCUITPROTECTEDBYA#LASS!GROUND

fault circuit interrupter.

s4OENSURECONTINUEDPROTECTIONAGAINSTSHOCKHAZARDUSE

only identical replacement parts when servicing.

s)NSTALLASUITABLYRATEDSUCTIONGUARDTOMATCHTHE

maximum flow rate marked.

Warning:

s7ATERTEMPERATUREINEXCESSOFª#MAYBEINJURIOUSTO

your health.

s$ISCONNECTTHEELECTRICALPOWERBEFORESERVICING

Attention:

s4OUJOURSVERIFIERLEFFICACITEDUDISJONCTEURDIFFERENTIELAVANT

d’utiliser differentiel avant d’utiliser le bain.

s,IRELANOTICETECHNIQUE
s,ORSQUELAPPAREILLAGEESTINSTALLEDANSUNEFOSSEONDOIT

assurer un drainage adequat.

s%MPLOYERUNIQUEMENTALINTERIEURDUNECLOTURE#3!

Enclosure 3.

s#ONNECTERUNIQUEMENTAUNCIRCUITPROTEGEPARUN

disjoncteur differentiel de Class A.

s!FINDASSURERUNEPROTECTIONPERMANENTECONTRELEDANGER

de shock electrique, lors de l’entretien employer seulement 
des pieces de rechange identiques.

s,ESPRISESDASPIRATIONDOIVENTETREEQUIPEESDEGRILLES

convenant au debit maximal indique.

Avertissement:

s$ESTEMPERATURESDELEAUSUPERIEURESAª#PEUVENT

presenter un danger pour la sante.

s$ECONNECTERDUCIRCUITDALIMENTATIONELECTRIQUE

avante l’entretien.

Warning/Advertissement:

s$ISCONNECTTHEELECTRICPOWERBEFORESEEEPACCESS

door closed.

s$ECONNECTERDUCIRCUITDALIMENTATIONELECTRIQUEAVANT

l’entretien. Garder la porte fermer.

GREEN

WHITE

WHITE AC (120 V)

FOR W-WIRES

RED AC (240 V)

FOR W-WIRES

BLACK

RED

FROM GFCI

J23  J19  J28
J43  J42  J48

J53  J54
J55  J25
J26   

Warning! GFCI Protection.

The Owner should test and reset the GFCI on a regular 
basis to verify its function.

Warning!

  

Qualified technician required for service and installation.

Summary of Contents for GL Series













Reviews: