background image

Copyright 1998 Baker Hughes Company.

2 | DPI610A Instruction Manual–English

Specification

Note: 

For further general specification and functionality details refer to the standard DPI

 

610/615 

Series Portable Calibrator data sheet.

Parameter

Value

Pressure Safety

Maximum Working Pressure

2 x full-scale

Ranges

Altitude

-3000 to 50,000

 

ft

Airspeed

0 to 600

 

knots

Precision

over the airspeed range:
200

 

knots

±3

 

knots

400

 

knots

±0.7

 

knots

over the altitude range:
sea level

±14 ft

10,000

 

ft

±18 ft

30,000

 

ft

±36 ft

Precision includes linearity, hysteresis and repeatability, 12

 

months 

measurement stability.

Temperature Effects

±0.004% of reading/°C (averaged over -10° to +40°C w.r.t. 20°C)
±0.002% of reading/°F (averaged over +14° to 104°F w.r.t. 68°F)

Power Supply

Batteries

6 x 1.5 V C-cells, alkaline (up to 60

 

hours 

nominal use at 20°C)

Rechargeable

Ni-Cad battery pack (20

 

hours nominal use) 

supplied with charger/adaptor, supplies 

power to instrument while charging batteries.

Environment

Operating Temperature:

-10°C to 50°C (+14°F to 122°F) 

Calibrated Temperature:

-10°C to 40°C (+14°F to 104°F)

Ingress Protection

IP54 (NEMA 4)

Physical

Size:

300 x 170 x 140 mm (11.8" x 6.7" x 5.5")

Weight:

3

 

kg (6.6

 

lb)

Summary of Contents for Druck DPI 610A





















Reviews: