Baker Hughes Consolidated 2900 series Maintenance Manual Download Page 61

Page: 61 / 100

XIX. Reassembly of Pilot Valve

A. Lubricants and Sealants

1. Lubricate all O-Rings, except those made from

silicone, and spring seals sparingly with silicone
grease BHGE P/N SP505.

2. Seal all pipe threads with Teflon tape or pipe

sealant (BHGE P/N SP364-AB).

3. Lubricate standard threads and bearing points

with Flourolube GR362 (BHGE P/N 4668601)

or equivalent.

B. Assembly of 39PV07/37

1. Making the Main Pilot.

2. Making the Adjuster Assembly,

This assembly consists of:

1 – Adjuster Bottom

1 – Adjuster Top

1 – Spring Seal (Adjuster Top)

1 – O-Ring (Adjuster Top)

1 – O-Ring (Adjuster Bottom)

a. Check the Adjuster Top for burrs at the spring

seal lead in chamfer. Remove any burrs using

a polishing cloth.

b. Install Spring Seal (Adjuster Top) into Adjuster

Top using insertion tool as shown in Figure 80.
i. Lubricate Spring Seal (Adjuster Top) with

silicone grease.

ii. Install Spring Seal (Adjuster Top) onto

Plunger Cylinder with spring facing away

from Plunger Cylinder.

iii. Insert Plunger into Plunger Cylinder

until Plunger lightly contacts Spring Seal
(Adjuster Top).

iv. Insert Funnel Tube, chamfer side first,

over the Plunger and Spring Seal (Adjuster
Top). Stop when Spring Seal (Adjuster Top)
is about half way inside the Funnel Tube as
shown in Figure 46.

v. Remove Plunger.
vi. Insert Funnel Tube Assembly into Adjuster

Top until Funnel Tube contacts Spring Seal
(Adjuster Top) gland.

viii. Push down on Plunger cylinder to insert

Spring Seal (Adjuster Top) into Adjuster Top

as shown in Figure 47.

viii. Remove Funnel Tube Assembly.
ix. Inspect Adjuster Top to make sure that

Spring Seal (Adjuster Top) did not flare out
during installation and that the Spring Seal
(Adjuster Top) is oriented as shown in

Figure 48.

c. Thread Adjuster Top clockwise onto Adjuster

bottom and torque to 27±2 ft-lbs (37± 2.7 N-m).

d. Lubricate Main Piston stem and cycle Main

Piston through Spring Seal (Adjuster Top) five
times.

Spring Seal

(Main Piston)

Funnel Tube

Plunger Cylinder

Plunger

Figure 46: Funnel Tube

Adjuster Top

Plunger Cylinder

Spring Seal

(Adjuster Top)

Funnel Tube

Figure 47: Plunger Cylinder

Spring Seal (Insert)

Adjuster Top

Adjuster Bottom

Figure 48: Adjuster Top Assembly

Consolidated 2900 Series POSRV Maintenance Manual

Summary of Contents for Consolidated 2900 series





































































































Search results

Summary of Contents for Consolidated 2900 series

Reviews:

Related manuals for Consolidated 2900 series

Brands by name

Popular brands

Baker Hughes Consolidated 2900 series, Maintenance Manual

Search results

Summary of Contents for Consolidated 2900 series

Reviews:

Related manuals for Consolidated 2900 series

Brands by name

Popular brands