Baker Hughes Consolidated 2900 series Maintenance Manual Download Page 13 | Manualshive

Page: 13 / 100

background image

VI. Handling and Storage

Never attempt to lift the

valve by anything other

than the eyebolts.

Do not subject valves

to sharp impact.

Always keep valve in an

upright position when

handling or storing.

Handling

Always keep the inlet flange down on a crated or uncrated flange valve to prevent
misalignment and damage to valve internals.

Pilot Operated Safety Relief Valves should be handled carefully. The internal parts
of a pilot operated safety relief valve are precision machined and fitted together
to maintain perfect alignment. Rough handling may damage the external tubing,
pilot, and main valve seats or may cause misalignment sufficient to incur leakage or
erratic operation. POSRVs are shipped with a protective covering over the inlet and
the outlet flanges. This is to prevent damage to the flanged surfaces and to prevent
entry of foreign material into the valve.

ATTENTION!

Never lift the full weight of the valve by the pilot

assembly, external devices or tubing.

ATTENTION!

Do not rotate the valve horizontally or lift/carry using the pilot assembly.

ATTENTION!

Only lift the valve by the eyebolts inserted into the cover plate.

ATTENTION!

Handle carefully. Do not drop or strike the valve.

Storage

Store POSRVs in a dry environment and protect them from the weather. Do not
remove the valve from the skids or crates until immediately before installation. Do
not remove flange protectors and seating plugs until the valve is ready to be bolted
into place during the installation, i.e., both inlet and outlet.

Consolidated 2900 Series POSRV Maintenance Manual

|

13

© 2018 Baker Hughes, a GE company. All Rights Reserved.

«
...
11
12
13
14
15
...
»

Summary of Contents for Consolidated 2900 series





































































































Reviews:

No comments

Related manuals for Consolidated 2900 series

Brand: Calpeda Pages: 4

Brand: Federal Signal Corporation Pages: 34

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

Brand: YOKOGAWA Pages: 150

Brand: YOODA Pages: 3

Brand: YMGI Pages: 8

Brand: Parker Pages: 38

Brand: Parker Pages: 2

infi 90 IMMFP12

Brand: Bailey Pages: 75

iSteam 2.0 Control

Brand: mr. steam Pages: 16

Brand: Sygonix Pages: 12

Brand: Dejero Pages: 24

Brand: WINDY NATION Pages: 16

Brand: Kaba Mauer Pages: 10

Brand: Grundfos Pages: 20

Brand: One for All Pages: 15

Serial Interface Module

Brand: Federal Signal Corporation Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands