Baker Hughes Consolidated 2900 series Maintenance Manual Download Page 58

Page: 58 / 100

XVII. Disassembly of Pilot Valve (Contd.)

Note 1: Standard material is a filter plug. For special

materials, vent assembly is supplied.

D. Cleaning

1. Clean parts to remove all rust, burrs, scale, organic

matter, and loose particles. Parts are to be free of
any oil or grease except for lubrication as specified
in this instruction.

2. Cleaning agents used shall be such that effective

cleaning is assured without injuring the surface
finishes or material properties of the part.

3. Acceptable cleaning agents include demineralized

water, nonphosphate detergent, acetone, and
isopropyl alcohol. Parts must be blown dry or wiped
dry after cleaning.

4. If you are using cleaning solvents, take precautions

to protect yourself from potential danger from
breathing fumes, chemical burns, or explosion. See
the solvent’s Material Safety Data Sheet for safe
handling recommendations and equipment.

5. Do not “sand blast” internal parts as it can reduce

the dimensions of the parts.

Follow

recommendations

for safe handling in

the solvent's Material

Safety Data Sheet and

observe safe practices

for any cleaning

method

Part

No.

Nomenclature

Main Base

Adjuster Cap

Adjuster Top

Adjuster Bottom

Adjuster Lock Nut

Compression Screw

Compression Screw Lock Nut

Spring Washer

Spring

Insert Top

Insert Bottom

Main Piston

Cap (Compression Screw)

Cap Screw (Top Plate)

O-Ring (Adjuster Bottom)

O-Ring (Adjuster Top)

O-Ring (Insert)

O-Ring (Top Plate)

Bonnet

Spring Seal (Main Piston)

Spring Seal (Adjuster Top)

Spring Seal (Insert)

Field Test Connector

Vent Assembly/Bug Screen

(Field Test Connection)

Vent Assembly (Bonnet Vent)1

Set Screw (Bonnet)

Piston Nose

Piston Retainer Nut

Set Screw (Piston)

Vent Seal (Adaptor)

Spring Seal (Vent Seal Adaptor)

Back-up Ring (39MV72 Only)

Top Plate

58 | BHGE

Summary of Contents for Consolidated 2900 series





































































































Search results

Summary of Contents for Consolidated 2900 series

Reviews:

Related manuals for Consolidated 2900 series

Brands by name

Popular brands

Baker Hughes Consolidated 2900 series, Maintenance Manual

Search results

Summary of Contents for Consolidated 2900 series

Reviews:

Related manuals for Consolidated 2900 series

Brands by name

Popular brands