BainUltra AMMA BALNEO Owner'S Manual Download

Page: 18 / 63

Ground Wire

for the Bathtub

Turbine Female

Connector

Geysair Male

Connector

2-5

OWNER’S MANUAL

| INSTALLATION INSTRUCTIONS

1 800 463.2187

Monday to Thursday from 8 a.m. to 6 p.m. (EST) . Friday from 8 a.m. to 5 p.m. (EST)

BALNEO

- NAOS & SANOS

INSTALLATION

2. INSTALLATION (cont’d)

LEAK TEST

Once plumbing is fully installed and before

beginning any other work, fill the ThermoMas-

seur

to overflow and wait 30 minutes. Check all

plumbing hook-ups and bath for leaks. BainUltra

is not responsible for any water damage caused

by improper installation (see Warranty section).

ELECTRICITY

Install turbine and InMix power module con-

nections according to specifications outlined in

the Mia ELECTRICAL INSTALLATION - TURBINE

section.

NOTES

• Since these models sit directly on the floor, the overflow drain pipe opening is factory-drilled.

• To install the Naos or Sanos on a concrete slab with no access below for air entry to the bath: a hole

of 1 5/8 inch (4.1 cm) in diameter must be drilled into the bath skirt to allow air supply to the bath.

IMPORTANT

: Do not drill above height of existing hole in the skirt intended to connect drain to overflow.

2-5

For Geysair-equipped baths, connect

the Geysair electrical wire with the

male connector with the turbine cable

equipped with the female connector.

Test for grounding continuity between

the bath grounding terminal

and

the bath power supply. Failure to

perform the grounding continuity test

could result in serious personal injury.

2-6

For Geysair-equipped baths, the Gey-

sair unit must be connected to the hot

water supply with a 3/8 male compres-

sion or 1/2“ male NPT hose bibb. A

T and a valve (not supplied) must be

installed at the hot water intake.

Summary of Contents for AMMA BALNEO
































































Search results

Summary of Contents for AMMA BALNEO

Reviews:

Related manuals for AMMA BALNEO

Brands by name

Popular brands

BainUltra AMMA BALNEO, Owner'S Manual

Search results

Summary of Contents for AMMA BALNEO

Reviews:

Related manuals for AMMA BALNEO

Brands by name

Popular brands