background image

39

  BF-DM-C-DP E10-EN November 2019

DEALER MANU

AL FOR DISPL

A

Y

7.8 ERROR CODE DEFINITION

The display can show the errors of a pedelec. When the fault is detected, the error 
code will be displayed through the level indicator in flashing. Level 1 indicates the 

tens digit of an error code while level 2 indicates the units digit. For example:

1) Error code 04
The LED indicator for level 1 does not light, and level 2 flickers for 4 times. After 1 second pause, repeat the pattern. 
2) Error code 11
The level 1 flickers one time, then level 2 flickers one time. After 1 second pause, repeat the pattern.

Note:

 Please read carefully the description of the error code. When the error code appears, please first restart the 

system. If the problem is not eliminated, please contact your dealer or technical personnel.

Error

Declaration

Troubleshooting

04

The throttle is not back in its 
correct position.

Check the connector from the throttle is correctly 
connected. If this does not solve the problem, please 
change the throttle.

05

The throttle has fault.

1. Check the connector and cable of the throttle are
not damaged and correctly connected.

2. Disconnect and reconnect the throttle, if still no
function please change the throttle.

07

Overvoltage protection

1. Remove and re-Insert the battery to see if it
resolves the problem.

2. Using the BESST tool update the controller.

3. Change the battery to resolve the problem.

08

Error with the hall sensor signal 
inside the motor

1. Check all connectors from the motor are correctly
connected.

2. If the problem still occurs, please change the
motor.

09

Error with the Engine phase’s

Please change the motor.

10

The temperature inside the en-
gine has reached its maximum 
protection value

1. Turn off the system and allow the Pedelec to cool
down.

2. If the problem still occurs, please change the
motor.

11

The temperature sensor inside 
the motor has an error

Please change the motor.

12

Error with the current sensor in 
the controller

Please change the controller or contact your supplier.

Level 1

Level 2

Summary of Contents for DP C10.CAN












































Reviews: