manualshive.com logo in svg

Bad Boy Mowers EXTREME, Owner'S, Service & Parts Manual, Page: 40 / 72

Share
Download
Bad Boy Mowers EXTREME Owner'S, Service & Parts Manual Download Page 40

PAGE  40 

SECTION 4: 

ELECTRICAL SYSTEM 

This mower is equipped with one protective fuse: a 30-

amp main fuse (pictured to the right).  

A blown fuse usually indicates a problem within the 

electrical system or an electrical component. Ensure the 

battery terminals are tightly fastened. Never replace a 

fuse with one of a higher amperage rating or ‘bypass’ a 

fuse in any way. Doing so creates a significant fire hazard 

and can cause severe damage to the mowers electrical 

components. If a fuse is repeatedly blowing, contact your 

Bad Boy dealer.  

On most models, the red wire coming out of the engine is 

the charging wire from the alternator. Check for 13.6 - 

14.2 volts dc at this wire with engine at full throttle.  

If you are having issues starting your mower ensure the 

signal wire is connected to your starter solenoid.  

Check the condition and connection of the relays located 

under the control panel. Ensure that they are clean and 

connected. Make sure that wire terminal ends have not 

been pushed out of the relay block.  

Summary of Contents for Mowers EXTREME









































































Reviews:

No comments