Bad Boy Mowers EXTREME Page 30 Owner'S, Service & Parts Manual Download

Page: 30 / 72

PAGE 30

275 YAMAHA

(CONTINUED)

The fuel filter is located in the fuel line about 12˝ from the

carburetor on the side of the engine. Replace the filter

yearly. Prior to the removal of the old filter, note the

direction of fuel flow as indicated on the filter. Have

towels readily available in order to quickly remove any

fuel leakage. Always use new hose clamps and ensure

the security of the new filter by lightly pulling on each

hose. Always perform maintenance outdoors or in a well-

ventilated area. Do not smoke or allow any open flames

in the vicinity of any maintenance activities.

CHANGING YOUR FUEL FILTER

Locate your fuel filter and mark the direction it is

facing.

Clamp each side of the fuel filter to minimize and

gas spills.

Remove the clips from each side of the fuel filter

and remove the fuel filter.

Place the new fuel filter in the same direction as

the old and place clips back into place and

remove clamps.

Summary of Contents for Mowers EXTREME









































































Search results

Summary of Contents for Mowers EXTREME

Reviews:

Related manuals for Mowers EXTREME

Brands by name

Popular brands

Bad Boy Mowers EXTREME, Owner'S, Service & Parts Manual

Search results

Summary of Contents for Mowers EXTREME

Reviews:

Related manuals for Mowers EXTREME

Brands by name

Popular brands