Bad Boy Mowers EXTREME Page 22 Owner'S, Service & Parts Manual Download

Page: 22 / 72

PAGE 22

SECTION 3:

ENGINE

KOHLER CONFIDANT 747CC

This machine has an oil drain hose installed on the

engine to allow for easier oil changes. Bad Boy

recommends that the oil and filter be changed after the

initial 8hrs. of use, and at intervals of 50 usage hours or

yearly, whichever occurs first after that. The oil capacity is

2 quarts. Bad Boy 10W-30 synthetic blend engine oil is

recommended for maximum protection.

CHANGING YOUR ENGINE OIL AND OIL FILTER

Remove oil dipstick and open oil drain. Allow oil

to completely drain. (Make sure to have an oil

pan ready to capture old oil and properly dispose

old oil.)

The oil filter is located on the right side of the

engine. Clean area around oil filter. Place a

container under the oil filter to capture any oil and

remove filter. Wipe off mounting surface and

reinstall drain plug. Torque to 10 ft.*lbs.

Place new filter in shallow pan with open end up.

Fill with new oil until oil reaches the bottom of the

threads. Allow two minutes for oil to be absorbed

by filter material.

Apply a thin film of clean oil to rubber gasket on

new filter.

Refer to instruction on oil filter for proper

installation.

Fill crankcase with approximately 2 quarts of new

oil. Level should reach top of indicator on

dipstick.

Reinstall oil filter dipstick and tighten securely.

Start engine; check for oil leaks. Stop Engine;

correct oil leaks. Recheck oil level.

Dispose of used oil and filter in accordance with

local ordinances.

Summary of Contents for Mowers EXTREME









































































Search results

Summary of Contents for Mowers EXTREME

Reviews:

Related manuals for Mowers EXTREME

Brands by name

Popular brands

Bad Boy Mowers EXTREME, Owner'S, Service & Parts Manual

Search results

Summary of Contents for Mowers EXTREME

Reviews:

Related manuals for Mowers EXTREME

Brands by name

Popular brands