Bad Boy Mowers EXTREME Page 19 Owner'S, Service & Parts Manual Download

Page: 19 / 72

PAGE 19

CHANGING YOUR HYDRAULIC OIL AND FILTER
EXTREME 5400

Place an oil drain pan (12” or more in diameter

and 8 qt. capacity is optimal) beneath the oil

filter.

Remove the oil filter cover from the

transaxle to

drain the oil. Remove the O-ring from

the cover

and discard the O-ring.

After the oil has drained from the transaxle,

remove the oil filter from the transaxle housing.

Install a new filter and a new O-ring onto the filter

cover and install the filter cover. Torque the filter

cover to 200-300 in.-lbs.

Remove the top oil fill vent port plug as seen in

the picture to the right. Fill the transaxle with new

20W-50 through the hydraulic reservoir tank until

the oil reaches the oil fill vent port.

Install the top oil fill vent port plug and continue

filling the system with oil until the fill line is

reached in the expansion tank.

Drain the old oil filter of all free-flowing oil prior to

disposal. Place used oil in appropriate containers

and deliver to an approved recycling collection

facility.

Proceed to the purge procedure on page 20.

Recheck oil level and fill as necessary.

Outlaw Extreme transaxles hold 4.75 quarts each. Bad

Boy Hydrostatic Oil is recommended. Transaxle service is

recommended after the first 75 hours of use; then at

intervals of 250 usage hours. Use only Hydro-Gear®

brand oil filters. Use of other brands could void the

warranty.

Summary of Contents for Mowers EXTREME









































































Search results

Summary of Contents for Mowers EXTREME

Reviews:

Related manuals for Mowers EXTREME

Brands by name

Popular brands

Bad Boy Mowers EXTREME, Owner'S, Service & Parts Manual

Search results

Summary of Contents for Mowers EXTREME

Reviews:

Related manuals for Mowers EXTREME

Brands by name

Popular brands