Bad Boy Mowers EXTREME Page 13 Owner'S, Service & Parts Manual Download

Page: 13 / 72

PAGE 13

SECTION 7:

CONTROLS

7.1

Ignition Switch:

Bad Boy mowers have a three-position ignition switch: off, run, and start. With key

inserted, rotate it clockwise to START position and release key when engine starts, and switch will

automatically return to the RUN position.

7.2

Throttle Control:

A cable is connected to the engine throttle for controlling engine speed. Move lever

forward to increase engine rpm, move lever backward to decrease engine rpm.

7.3

Choke Control:

The choke control, located to the right of the operator’s left, is a ‘push-pull’ type.

When the choke knob is pushed in, the choke is in the off (run) position. When the choke is pulled out it

is in the on (start) position. Do not operate the machine in the on (start) position.

7.4

Control Levers: (Not Shown) These levers control the mower’s speed, direction, and neutral lock.

These levers are used to steer, accelerate, decelerate and change direction.

7.5

Blade Engage Switch: This switch engages the blades. Pull the switch up to engage the blades and

push the switch down to disengage the blades.

7.6

Parking Brake: This lever engages the parking brake. Pull back fully to engage the parking brake;

push forward to disengage.

7.5

7.3

7.2

7.1

7.6

Summary of Contents for Mowers EXTREME









































































Search results

Summary of Contents for Mowers EXTREME

Reviews:

Related manuals for Mowers EXTREME

Brands by name

Popular brands

Bad Boy Mowers EXTREME, Owner'S, Service & Parts Manual

Search results

Summary of Contents for Mowers EXTREME

Reviews:

Related manuals for Mowers EXTREME

Brands by name

Popular brands