Bad Boy 1022H Operator'S Manual Download

Page: 119 / 148

MAINTENANCE

(1) Inspection

Perform inspection with the engine

stopped.

①

Check the transmission fluid lev

el through the sight glass to see if

the level is between the upper and

lower limits.

②

If insufficient, add oil.

(2) Changing

Perform inspection with the engine

stopped.

①

Unscrew the drain plug on the

lower section of the transmission

to drain contaminated transmis

sion fluid. Since hot fluid flows out

of the engine first, be careful not

to get burnt.

②

After draining fluid, tighten the

transmission fluid drain plug.

③

Add the specified amount of

the specified transmission fluid

through the filler hole

TRANSMISSION FLUID

(1) Transmission Fluid Filler Hole

(1) Drain Plug

Upper

limit

Lower

limit

BB1022H.indb 9

2021-06-28 오후 5:53:28

Summary of Contents for 1022H





















































































































































Search results

Summary of Contents for 1022H

Reviews:

Related manuals for 1022H

Brands by name

Popular brands

Bad Boy 1022H, Operator'S Manual

Search results

Summary of Contents for 1022H

Reviews:

Related manuals for 1022H

Brands by name

Popular brands