Page 2
Measuring Your Railing Area
Important Information
Component Dimensions
Tools Required
Components Needed For Installing
One Contemporary Style Rail Section
• Measurements are from center to center of post. Packs are
produced to 6’ and 8’ to allow for finished end cuts and angles.
• Determine how many 6’ or 8’ Contemporary Rail packs you
need and check to be sure you have all the components
(and quantities) listed in the chart and shown to the right.
• Cable Cutters
• Extended 1/4”
drill bit
• 2 - 3/8” open-
ended wrenches
• Miter Saw (blade
designed for
finished cuts)
• Drill
• Drill Bits: 1/4”,
3/16”, 1/8”, 9/64”
• Tape Measure
• #2 square drive
Hardware included in
Hardware Kits:
Components available
in Mix-and-Match Rail
Systems
Additional Components
Needed for Each
System
2 - Universal Rails
Hardware Mounting Kit
8 - Top Rail screws
Foot blocks
- 2 in 6’ Pack
- 3 in 8’ Pack
4 - Hinged Brackets
11 - #10x2” Screws
8 - #10x7/8” Screws
4 - #10x1/2” Screws
T25 Torx Driver Bit
36” Intermediate Baluster
- 1 for 6’ -2 for 8’
42” Intermediate Baluster
- 1 for 6’ -2 for 8’
Stair Intermediate Baluster
- 1 for 6’ -2 for 8’
Cable
- 100’ spool or 500’ spool
36” Hardware Kit
- 9 Quick Connect Fittings
- 9 Quick Connect Swivel
Fittings
- 18 Hanger Bolts
- 9 Lock Nuts
42” Hardware Kit
- 11 Quick Connect Fittings
- 11 Quick Connect Swivel
Fittings
- 22 Hanger Bolts
- 11 Lock Nuts
2 - Post Sleeves
2 - Post Skirts
1 - Contemporary Top Rail
End Coating- optional
CableRail Accessory Pack
Includes:
- Quick-Connect Release Tool
- Lacing Needle
- Hanger Bolt Installation Tool
Protector Sleeves
- 42” system: 22 per through post
- 36” system: 18 per through post
Contemporary Rail Pack
CableRail Components
5”
.75”
5”
.75”
Intermediate
Baluster
Intermediate Base
Plate
Top Rail
Post Sleeve
CableRail
(9 Cables for 36”)
(11 Cables for 42”)
Top Rail (1)
Hinge Bracket (4)
Intermediate
Base Plate (1 for
each Intermediate
Baluster)
Intermediate
Baluster
(1 for 6’)
(2 for 8’)
Universal Rail (2)
Post Sleeve (2)
Post Skirt (2)
Foot Block
(3 in 8’ Section)
(2 in 6’ Section)
Evolutions Rail
TM
Contemporary Rail Packs are
available in 6’ or 8’ lengths.
Quick-Connect
Fitting
Quick-Connect
Swivel Fitting
Protector
Sleeve
Universal Rail
Hinge
Bracket
2.225”
.900”
1.25”
6.35”
• Contemporary Style 6’ and 8’ Packs are designed not to
exceed 6’ and 8’ center of post to center of post, respectively.
• Cut slowly, using a fine tooth saw blade to avoid chipping.
• For 42” railing, use 8’ Post Sleeves.
• Evolutions Rail Contemporary Style is designed and tested solely for
over the post applications with the top rail profile affixed to the top of the
structural 4x4.
• This does not include applications where the 4x4 posts extend above or
through the top rail profile.
• Evolutions Rail Contemporary requires a top rail profile (deck plank) to
complete the system for a proper installation and code compliance.
Visit www.timbertech.com/installation to view TimberTech installation videos.
Consult your local building codes for guard and handrail requirements.
Installing Evolutions Rail
TM
Contemporary
with CableRail by Feeney
®
