Azbil MY8045A Specifications & Instructions Download Page 2

AB-6682 

Safety Instructions 

Please read instructions carefully and use the product as specified in this manual.  Be sure to keep this manual near by for ready 
reference.  

Usage Restrictions 

This product is targeted for general air conditioning.  Do not use this product in a situation where human life may be affected.  If 
this product is used in a clean room or a place where reliability or control accuracy is particularly required, please contact Azbil 
Corporation’s sales representative.  Azbil Corporation will not bear any responsibility for the results produced by the operators.

 

  WARNING  

 

  Do not disassemble the product.  Disassembly may result in electrical shock or equipment damage. 

 

  CAUTION 

 

  This product must be operated under the operating conditions (power, temperature, humidity, vibration, shock, 

installation position, atmospheric condition, etc) specified in this manual to prevent equipment damages. 

 

  This product must be operated within its rated operating ranges specified in this manual.  Failure to comply will 

cause equipment damages. 

 

  Operate the product within the service life, and avoid application that keeps product operating cycle excessively 

frequent.  Overuse of the product may shorten the product service life. 

 

  Installation and wiring must be performed by qualified personnel in accordance with all applicable safety 

standards. 

 

  Do not install the product in a location with high temperature radiation.  High temperature radiation may result in an 

actuator malfunction. 

 

  Do not put heavy load on the product.  It may get damaged. 

 

  All wiring must comply with local codes of indoor wiring and electric installation rules. 

 

  This product does not have a power switch.  Be sure to provide a power circuit breaker in the power source. 

 

  To prevent product damage, always disconnect the power supply from the product before performing installation 

and wiring. 

 

  Make sure all the wires are tightly connected.  Incomplete connection may result in an actuator malfunction. 

 

  Do not touch the moving part of the product in operation to prevent personal injury. 

 

  Dispose of this product as an industrial waste in accordance with your local regulations.  Do not reuse all or part of 

this product. 

 
Trademark information: 
ACTIVAL, Infilex, and savic-net are trademarks of Azbil Corporation in Japan or in other countries. 
BACnet is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE). 

Summary of Contents for MY8045A













Reviews: