Axon Synapse HCS100 Installation, Operation And Upgrade Manual Download

Page: 28 / 44

LED Indication

Introduction

LEDS are located on the front of the card next to the card grip as
shown in the picture below. The LEDS give an indication of the status
of the HCS100.

Error LED

The error LED indicates an error if the internal logic of the card is not
configured correctly or has a hardware failure.

Input_1 LED

This LED indicated the presence of a valid SDI video signal on input 1.

Input_2 LED

This LED indicated the presence of a valid SDI video signal on input 2.

ANC Data LED

Indicates the presence of embedded audio within the input signal.

Reference LED

Indicated the presence of a valid reference signal on the selected
reference input connector (ref-1 or ref-2).

Data Error LED

This LED indicates a CRC error.

Connection LED

This LED illuminates after the card has initialized. The LED lights for
0.5 seconds every time a connection is made to the card.

Error LED

The error LED indicates an error if the internal logic of the card is not
configured correctly or has a hardware failure.

Summary of Contents for Synapse HCS100













































Search results

Summary of Contents for Synapse HCS100

Reviews:

Related manuals for Synapse HCS100

Brands by name

Popular brands

Axon Synapse HCS100, Installation, Operation And Upgrade Manual

Search results

Summary of Contents for Synapse HCS100

Reviews:

Related manuals for Synapse HCS100

Brands by name

Popular brands