Axminster 107634 Original Instructions Manual Download Page 21 | Manualshive

Page: 21 / 28

background image

Maintenance

21

WARNING! ALWAYS WEAR A DUST MASK

WARNING! ALWAYS WEAR EYE PROTECTION

Daily

• Empty the collection bag before it overflows, wear a dust mask

whilst removing and emptying the bag.

Weekly

• Check the inlet and outlet duct and remove any accumulated

sawdust.

•Check the inlet hoses for splits and cracks, repair as necessary.

• Check the dust collection bag for wear and tear, especially

around the neck of the retaining belt. If wear or fraying is
occurring, replace the bag.

• Check the motor for dust, sawdust, shavings etc, build up. If

this has occurred, clean with a vacuum cleaner, see fig 58.

• Move the shaker paddle handle back and forth to remove any

built up dust and debris from inside the filter.

Monthly

• Remove the filter securing belt and remove the filter assembly,

see fig 59 using an ‘M’ class vacuum cleaner, clean inside the
filter.

Basic Maintenance

Fig 58-59

Clean the motor housing vents

«
...
19
20
21
22
23
...
»

Summary of Contents for 107634





























Reviews:

No comments

Related manuals for 107634

POWERbot SR20J925 Series

Brand: Samsung Pages: 56

Brand: Daewoo Pages: 31

Brand: Daewoo Pages: 4

Brand: DAEWOO ELECTRONICS Pages: 30

Brand: Kroll Pages: 28

Brand: Coopers Pages: 4

Brand: Shark Pages: 16

Tornado Cylinder

Brand: Daewoo Pages: 10

PowerForce 6594 Series

Brand: Bissell Pages: 16

Brand: Kogan Pages: 16

Brand: Numatic Pages: 16

Brand: Parker Pages: 36

Viroxid HABITAT 3 AIR 160

Brand: IDS Pages: 28

Brand: Cleanmaxx Pages: 44

Brand: U-Line Pages: 26

Rapide Supreme V-023

Brand: Vax Pages: 16

STEAMTEC STEAMTEC 5 IH

Brand: Nilfisk-ALTO Pages: 72

Brand: Trotec Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands