Axis P3384-VE User Manual Download Page 52 | Manualshive

Page: 52 / 67

background image

AXIS P3384–V Fixed Dome Network Camera

System Options

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see

Reset to Factory Default Settings on page 56

.

UPnP

TM

The Axis product includes support for UPnP

TM

. UPnP

TM

is enabled by default and the product is automatically detected by operating

systems and clients that support this protocol.

UPnP

TM

can be disabled under

System Options > Network > UPnP

TM

.

RTP/H.264

The RTP port range and multicast settings are configured under

System Options > Network > RTP

.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams,
only certain IP addresses and port numbers should be used.

Select

Always Multicast Video

and/or

Always Multicast Audio

to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating
systems and clients that support this protocol.

Bonjour can be disabled under

System Options > Network > Bonjour

.

Storage

SD Card

NO

NO

NOTICE

TICE

TICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

Note

For SD card recommendations see

www.axis.com

The Axis product supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHC or SDXC card
with speed class 10.

The following SD card file systems are supported:

•

ext4

— recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access

data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•

vFAT

— supported by most operating systems for personal computers.

The SD card is managed on the

System Options > Storage

page. Click

SD Card

to open

Storage Management

.

If the card’s status shows as failed, click

Check disk

to see if the problem can be found and then try

Repair

. This option is only

available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card.

To avoid filling the card, it is recommended to remove recordings continuously. Under

General Settings

, select

Remove recordings

older than

and select the number of days or weeks.

To stop writing to the card and protect recordings from being removed, select

Lock

under

General Settings

.

52

«
...
50
51
52
53
54
...
»

Summary of Contents for P3384-VE




































































Reviews:

No comments

Related manuals for P3384-VE

Brand: GE Pages: 115

Brand: I-G3N Pages: 28

Brand: iCamera Pages: 58

Brand: FALEEMI Pages: 12

Brand: Falconeyes Pages: 2

Brand: FalconEye Electronics Pages: 5

Brand: Digitus Pages: 9

Brand: FLIR Pages: 112

NVAHD-2DN3201MH/IR-1-PIR

Brand: Novus Pages: 32

Brand: CIS Pages: 23

Brand: Acebil Pages: 11

DH-IPC-HFW5421E-Z

Brand: Zhejiang Pages: 14

Brand: Fallowgate Limited Pages: 3

Brand: Olympus Pages: 31

Brand: Manfrotto Pages: 2

Electronic Automatic Focuser

Brand: ZWO Pages: 38

Brand: Conrad Pages: 10

Brand: Avigilon Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands