Axis P3384-VE User Manual Download

Page: 23 / 67

AXIS P3384–V Fixed Dome Network Camera

Video and Audio

For more information, see the online help

Important

Adding many privacy masks may affect the product’s performance.

Focus & Zoom

Focus and zoom should only be configured when installing or reinstalling the product.

For installation instructions, refer to the product’s Installation Guide.

See for more information.

To set focus and zoom:

1. Install the camera as described in the Installation Guide.

2. Go to

Video & Audio

Focus & Zoom

3. On the

Basic

tab, set the

zoom

level using the slider. The buttons < and > move the zoom position one step in either

direction. The buttons << and >> move the zoom position in multiple steps in either direction.

4. Click

Perform auto focus

to focus the camera automatically.

5. If more adjustments are needed, go to the

Advanced

tab.

Note

• Changing the zoom level moves the focus position. Focus should always be adjusted after changing the zoom.

• Movements in front of the camera should be avoided during automatic focusing.

On the

Advanced

tab, focus can be adjusted manually:

1. Click

Open iris

to open the iris to its maximum position. This gives the smallest depth of field and provides the best

conditions for focusing.

2. Focus is set in the

Focus window

. Use the mouse to move and resize the focus window.

3. Click in the

Focus position

bar to focus on a desired location. The buttons < and > move the focus position one step in

either direction. The buttons << and >> move the focus position in multiple steps in either direction.

4. When satisfied, click

Enable iris

to enable the iris.

Audio Settings

The audio functionality for each video stream is enabled under

Video & Audio

Video Stream

Audio

Audio Modes

The Axis product supports the following audio modes:

Full duplex -

Simultaneous two-way audio allowing the Axis product to transmit and receive audio at the same time. There is no

echo cancellation; if feedback loops appear, try moving the microphone or the speaker.

Half-duplex -

Audio can be transmitted to and from the Axis product but only in one direction at a time. To transmit audio using the

Live View page, use the

Talk

and

Listen

buttons, see

AMC Audio Controls on page 11

Simplex — Network Camera speaker only -

Audio is transmitted from a client to the Axis product and can be played by a speaker

connected to the product. To transmit audio using the Live View page, the

Talk

and

Microphone

buttons must both be active,

see

AMC Audio Controls on page 11

Summary of Contents for P3384-VE




































































Search results

Summary of Contents for P3384-VE

Reviews:

Related manuals for P3384-VE

Brands by name

Popular brands

Axis P3384-VE, User Manual

Search results

Summary of Contents for P3384-VE

Reviews:

Related manuals for P3384-VE

Brands by name

Popular brands