Axis P3384-VE User Manual Download

Page: 65 / 67

AXIS P3384–V Fixed Dome Network Camera

Technical Specifications

Connectors

I/O Connector

4-pin terminal block for:

• Auxiliary power (DC output)
• Digital Input
• Digital Output
• 0 V DC (-)

Function

Pin

Notes

Specifications

0 V DC (-)

0 V DC

DC output

Can be used to power auxiliary equipment.
Note: This pin can only be used as power out.

3.3 V DC
Max load = 50 mA

Digital Input

Connect to pin 1 to activate, or leave floating (unconnected)
to deactivate

0 to max 40 V DC

Digital Output

Connected to pin 1 when activated, floating (unconnected)
when deactivated. If used with an inductive load, e.g. a relay,
a diode must be connected in parallel with the load, for
protection against voltage transients.

0 to max 40 V DC, open drain,
100 mA

3.3 V max 50 mA

Audio Connector

3.5 mm audio connectors
(stereo)

Summary of Contents for P3384-VE




































































Search results

Summary of Contents for P3384-VE

Reviews:

Related manuals for P3384-VE

Brands by name

Popular brands

Axis P3384-VE, User Manual

Search results

Summary of Contents for P3384-VE

Reviews:

Related manuals for P3384-VE

Brands by name

Popular brands