manualshive.com logo in svg

Axion AC-AXION-4, User Manual

Share
Download
Axion AC-AXION-4 User Manual Download Page 40

40

HDBaseT lights: LINK

These ports are HDBaseT Transmitters (TX) and are designed to be connected via a Category cable (Cat6 or 

better) to an HDBaseT Receiver (RX)� 

NOTE: 

Non AVPro HDBaseT Receivers may work but ICT (our Invisible Compression Technology) will not� 

This means higher bandwidth signals (greater than 10�2Gbps) will not pass as this requires ICT� See Band-

width chart on Page 50� 

LINK - 

Above RJ45 (HDBT) Port: (Green)

(Green) This indicator shows that the AV HDBT link between the Tx 

and Rx is in tact� This light should ALWAYS

ALWAYS be SOLID

SOLID� 

If this light is flashing or not present attempt following:

 

1� Check the length� The maximum distances are 70m (230ft) on 4K and 100m (330ft) on 1080P�
2� Remove any coils of cable and make sure that there is not excess cabling�
3� Bypass all patch panels and punch-down blocks�
4� Re-terminate connectors� Sometimes, even if a cable tester indicates the run is valid, something may 

be slightly off.

a� Standard RJ45 ends are recommended� Pass through style types can cause interference/crosstalk

5� Contact AVProEdge if these suggestions do not work�

AVProEdge - HDBaseT Extender

Indicator Lights

Summary of Contents for AC-AXION-4























































Reviews:

No comments

Brands by name

Popular brands

Load more brands