background image

SBC856A1 Series All-in-One POS Board User’s Manual 

 

34 

Award BIOS Utility 

z

 

Drive A type/Drive B type 

The category identifies the types of floppy disk drive A or drive B installed 
in the computer. 

None 

No floppy drive installed 

360K, 5.25 in 

5.25 inch PC-type standard drive; 360Kb capacity 

1.2M, 5.25 in 

5.25 inch AT-type high-density drive; 1.2MB capacity 

720K, 3.5 in 

3.5 inch double-sided drive; 720Kb capacity 

1.44M, 3.5 in 

3.5 inch double-sided drive; 1.44MB capacity 

2.88M, 3.5 in 

3.5 inch double-sided drive; 2.88MB capacity 

z

 

Halt On 

This field determines whether the system will halt if an error is detected 
during power up. 

No errors 

The system boot will halt on any error 
detected. (default) 

All errors 

Whenever the BIOS detects a non-fatal 
error, the system will stop and you will be 
prompted. 

All, But Keyboard 

The system boot will not stop for a 
keyboard error; it will stop for all other 
errors. 

All, But Diskette 

The system boot will not stop for a disk 
error; it will stop for all other errors. 

All, But Disk/Key 

The system boot will not stop for a 
keyboard or disk error; it will stop for all 
other errors. 

Summary of Contents for SBC856A1








































































Reviews: