manualshive.com logo in svg

Axi MTC-X, Instruction, Operating And Maintenance Manual

Share
Download
Axi MTC-X Instruction, Operating And Maintenance Manual Download Page 5

5

O

VER

VIEW

REV0303MTCX010318

S

Y

S

TEM C

OMPONENT

S

PRIMING

MAINTENANCE

C

OMMISSIONING

PRIMAR

Y INSPECTION

OPERA

TION

General Overview

MTC-X 

Specifications

Note: The system is designed to meet environmental standards for safe operation. (Not for use with fluids that have a 

flash point below 100°F (37.8°C), e.g. gasoline, alcohol, etc.)

Flow Rate ................................................................................
Outline Dimensions (Enclosure) ............................................
System Weight .......................................................................
Operating Temperature ..........................................................
Electrical  .................................................................................
Pump .......................................................................................
Motor .......................................................................................
Fuel Conditioner .....................................................................
Inlet ..........................................................................................
Outlet(s) ..................................................................................

26 GPM/1560 GPH (98.4 LPM/5905 LPH)
48” x 22.5” x 25” (122 x 57 x 63 cm) (H x W x D)

≈ 185 lbs (84 kg)
41 - 104°F (5 - 40°C)

115V/60Hz/15A or 230V/50Hz/15A
Self Priming Rotary Vane Pump

3/4 HP single phase, thermally protected

LG-X 3000
1-1/2” NPT male port
1-1/4” NPT male port

O

VER

VIEW

Summary of Contents for MTC-X





































Reviews:

No comments

Brands by name

Popular brands

Load more brands