background image

5

© 2009 Directed Electronics. All rights reserved.

Sat mode,

bank selector

AUDIO

PWR

1

2

REW

FF

PLAY/PROG

NR

3

4

5

6

DISC-

DISC+

11:53

XM1-1

CH-001

CH

VOL

SCAN

SOUND

AM/FM

CD/AUX

SAT

RADIO

SEEK

SKIP

RPT

DISP -

MODE

A.SEL

RDM

TUNE

AUTO

OFF

DUAL

A/C

MODE

Channel control

Category

Control

Text selector.

Hold for 10sec to toggle

channel or category

tune modes.

Toggles

Scan mode

Bank and

present

indicator

Channel

and text

indicator

Preset 1-6.

Hold until beep to

save to a preset.

CATEGORY

Tune mode

indicator

MODE

DUAL

OFF

AUTO

MAP/

GUIDE

MENU

SETUP

INFO

ZOOM CANCEL AUDIO

AUTO

MODE

A/C

LOAD

DISC

TAPE

AM/FM

DISP

MODE

SCAN

RPT

A.SEL/RDM

- SEEK +

1

2

3

4

5

6

DISC-

DISC+

VOL

PWR

PUSH

TUNE

SOUND

PUSH

XM1-1

VOL

CH

CHANNEL

CATEGORY

NAME

TITLE

:

:

:

:

1

CH

2

CH

3

CH

6

CH

5

CH

4

CH

MODE

SCAN

SOUND

001 - HITS1

POP

MUSIC NAME

MUSIC TITLE

Channel control

Category

Control

001

014

018

040

065

115

Toggles between

channel and

category modes

Bank and

present

indicator

Upper display

text mode

selector

Sat mode

and bank

selector

Preset 1-6.

Press until

beep to save

to a preset.

Channel and text

Indicator fields

Toggles

Scan mode

Tune mode

indicator

ANTENN

A

SC OUTPUT

Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator

Headunit bus cable

SiriusConnect Cable

HON-SC1

Honda Bus 

Compatible

Translator 

Warning! Safety first

The following safety warnings must be observed at all times:

Due to the complexity of this system, installation of this product must only be 

• 

performed by an authorized Directed Electronics dealer.

When properly installed, this system can start the vehicle via a command 

• 

signal from the remote control.  Therefore, never operate the system in an 

area that does not have adequate ventilation. 

The following precautions are the sole responsibility of the user; however, autho-

rized Directed Electronics dealers should:

Never use a test light or logic probe when installing this unit. Always 

• 

use a multimeter.

 

Never operate the system in an enclosed or partially enclosed area without 

• 

ventilation (such as a garage). 

When parking in an enclosed or partially enclosed area or when having 

• 

the vehicle serviced, the remote start system must be disabled using the 

installed toggle switch. It is the user’s sole responsibility to properly handle 

and keep out of reach from children all remote controls to assure that the 

system does not unintentionally remote start the vehicle.

USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT 

THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING 

FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY EN-

CLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

 

Use of this product in a manner contrary to its intended mode of operation may 

result in property damage, personal injury, or death. Except when performing 

the Safety Check outlined in this installation guide, (1) Never remotely start the 

vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the 

keys in the ignition. The user will be responsible for having the neutral safety fea-

ture of the vehicle periodically checked, wherein the vehicle must not remotely 

start while the car is in gear. This testing should be performed by an authorized 

Directed  Electronics  dealer  in  accordance  with  the  Safety  Check  outlined  in 

this product installation guide. If the vehicle starts in gear, cease remote start 

operation immediately and consult with the user to fix the problem immediately. 

After the remote start module has been installed, test the remote start module 

in accordance with the Safety Check outlined in this installation guide. If the 

Summary of Contents for 5103

































































Reviews: