Avital 5103 Installation Manual Download Page 43

Page: 43 / 64

Feature menus

The default settings are indicated in bold type. Features that have additional set-

tings that can be programmed using the Bitwriter® are indicated with an asterisk

(*) The number in parenthesis indicates the number of times the LED flashes and

the horn honks.

➤

Menu 1 - Basic

Item

One-chirp setting

Two-chirp setting

Active Arming

Passive arming

Arm/disarm chirps on

Arm/disarm chirps Off

Ignition lock On

Ignition lock Off

Ignition unlock On

Ignition unlock Off

Active locking only

Passive locking

Panic with ignition On

No panic with ignition On

0.8 second door lock pulses (1)

3.5 (2), 0.4 (3) seconds

Forced passive arming on

Forced passive arming off

Automatic engine disable on

Automatic engine disable off

Armed When Driving (AWD) on

AWD Off

Code Hopping On

Code Hopping off

Horn Output Pulsed

Constant

Horn function Full Alarm Only (1)

Siren function - chirp length
20mS (2), 30mS (3), 40mS (4), 50mS
(5)

Comfort Closure ON

Comfort Closure OFF

(2),

Comfort Closure 2 (3)

Summary of Contents for 5103
































































Search results

Summary of Contents for 5103

Reviews:

Brands by name

Popular brands

Avital 5103, Installation Manual

Search results

Summary of Contents for 5103

Reviews:

Brands by name

Popular brands