Avital 2300 Installation Manual Download Page 18

Page: 18 / 33

auxiliary harness (H3) wire connection guide

______

This output is used for progressive door unlock. A progressive unlock system unlocks the driver's door when the

unlock (disarm) button is pressed and unlocks the passenger doors if the unlock (disarm) button is pressed again

within 15 seconds after unlocking the driver's door. The BLUE wire outputs a low current (-) pulse on the second

press of the unlock button of the transmitter. This negative unlock output is used to unlock the passenger doors.

NOTE:

The second unlock output feature is not available if the double pulse unlock feature is turned on.

IMPORTANT!

The H2/A wire is not required for wiring the door locks. Depending on the type of door

lock system, there may be additional wires in the Door Lock Harness (H2) that are not required
used in wiring the door locks.

H3/1 BLUE (-) 200mA second unlock output

VIOLET/BLACK

(-) 200 mA CHANNEL 4 OUTPUT

BROWN/BLACK

(-) 200 mA HORN HONK OUTPUT

BLUE

(-) SECOND UNLOCK

H3/1

H3/2

H3/3

Summary of Contents for 2300


































Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands

Avital 2300, Installation Manual

Search results

Summary of Contents for 2300

Reviews:

Related manuals for 2300

Brands by name

Popular brands