manualshive.com logo in svg

Avaya DEFINITY SERIES, Installation And Maintenance Manual, Page: 96 / 101

Share
Download
Avaya DEFINITY SERIES Installation And Maintenance Manual Download Page 96

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN  

555-233-121  

Issue 2

November 2000

SREPN Maintenance 

2-42

Restore from remote location 

2

The 

Table 2-13

 describes the conditions in which the restore from a remote 

location is possible.

Table 2-13.

TN2301 switch configuration based on input

 

Inputs to Control Logic

Modes

Remote 
restore

Survive 
mode 
requested

a

a.

The EPN Maintenance (TN775C) circuit pack requests switching to Survive mode.

Switch 
position

SRP 
power

State of SREPN

Not active

Not active

AUTO

Good

Normal mode: EPN connected with Release 9r 
PPN

Not active

Active

AUTO

Good

Survive mode: EPN connected to SRP 

Not active

Does not 
matter

TEST

Good

Survive mode: EPN connected to SRP

Active

Does not 
matter

TEST

Good

Survive mode: EPN connected to SRP

Not active

Does not 
matter

RSTR

Good

Normal mode: EPN connected to Release 9r 
PPN

Not active

Does not 
matter

RSTR

Bad

Normal mode: EPN connected with Release 9r 
PPN

Active

Does not 
matter

AUTO or
RSTR

Good

Normal mode: EPN connected to Release 9r 
PPN

Continued on next page

Summary of Contents for DEFINITY SERIES






































































































Reviews:

No comments