manualshive.com logo in svg

Avaya DEFINITY SERIES, Installation And Maintenance Manual, Page: 59 / 101

Share
Download
Avaya DEFINITY SERIES Installation And Maintenance Manual Download Page 59

DEFINITY Enterprise Communication Server Release 9
Installation and Maintenance for Survivable Remote EPN  

555-233-121  

Issue 2

November 2000

SREPN Maintenance 

2-5

SREPN connections 

2

Interfacing circuit packs

The Survivable Remote equipment can operate through:

■

‘‘Expansion Interface connections’’

■

‘‘DS1 CONV connections’’

Expansion Interface connections

■

TN570C Expansion Interface (EI) circuit packs use either the 9823A 
(multimode) or the 300A (single mode) transceivers.

NOTE:

A new SREPN system includes the TN570C EI circuit pack. Earlier EI 
circuit packs (for example, TN570B) are not supported.

DS1 CONV connections

■

TN1654 DS1 Converter supports T1/E1 remoting and wideband 
applications.

■

Standard and High Reliability systems use pairs of TN1654, not mixed with 
the earlier TN574.

■

Critical Reliability systems require TN1654 circuit packs on the duplicate 
pair.

Summary of Contents for DEFINITY SERIES






































































































Reviews:

No comments