Avaya DEFINITY SERIES Installation And Maintenance Manual Download Page 101

Page: 101 / 101

We’d like your opinion.

Lucent Technologies welcomes your feedback on this document. Your comments can be of great value
in helping us improve our documentation.

DEFINITY® Enterprise Communications Server Release 9 Installation and Maintenance for
Survivable Remote EPN, 555-233-121, Issue 2, November 2000

1. Please rate the effectiveness of this document in the following areas:

2. Please check the ways you feel we could improve this document:

Please add details about your concern.__________________________________________________

_________________________________________________________________________________

3. What did you like most about this document?___________________________________________

_________________________________________________________________________________

4. Feel free to write any comments below or on an attached sheet.____________________________

_________________________________________________________________________________

If we may contact you concerning your comments, please complete the following:

Name:_________________________________________Telephone Number: ( )

Company/Organization______________________________________Date:___________________

Address:_________________________________________________________________________

When you have completed this form, please fax to (303) 538-1741. Thank you.

Excellent

Good

Fair

Poor

Ease of Finding
Information
Clarity
Completeness
Accuracy
Organization
Appearance
Examples
Illustrations
Overall Satisfaction

❒

Improve the overview/introduction

❒

Make it more concise

❒

Improve the table of contents

❒

Add more step-by-step procedures/tutorials

❒

Improve the organization

❒

Add more troubleshooting information

❒

Add more figures

❒

Make it less technical

❒

Add more examples

❒

Add more/better quick reference aids

❒

Add more detail

❒

Improve the index

Summary of Contents for DEFINITY SERIES






































































































Search results

Summary of Contents for DEFINITY SERIES

Reviews:

Avaya DEFINITY SERIES, Installation And Maintenance Manual, Page: 101 / 101

Search results

Summary of Contents for DEFINITY SERIES

Reviews: