manualshive.com logo in svg

Avaya Cajun P880 Manager 5.1, Installation Manual, Page: 41 / 62

Share
Download
Avaya Cajun P880 Manager 5.1 Installation Manual Download Page 41

   2-16

Chapter 2

Cajun P550R/P880/P882 Switch Installation Guide

Table 2-7.  Module Front Panel LED Display Interpretations

Module...

LED...

Behavior.

..

Indicates...

All Modules

Module 
Status

Solid green

Normal operation.

Flashing 
yellow

Diagnostic failure.

Off

Module not operational or not 
receiving power.

Gigabit 
Modules

TX and 
RX

Flashing 
yellow

Port sending/receiving traffic.

Off

Port not sending/receiving 
traffic.

Port

Solid green

Port enabled with link up.

Flashing 
green

Port disabled with link up.

Flashing 
yellow

Hardware failure.

Off

No link.

HD/FD

Solid green

Full-duplex operation 
negotiated.

Flashing 
yellow

Hardware failure.

Off

No link.

10/100 
Modules

Port

Solid green, 
with yellow 
flash

Port enabled and sending and 
receiving traffic Traffic indicated 
by yellow flashes.

Flashing 
green

Port disabled with link up.

Flashing 
yellow

Hardware failure.

Off

No link.

Summary of Contents for Cajun P880 Manager 5.1































































Reviews:

No comments