AVANT A36883 Operator'S Manual For Attachment Download Page 29 | Manualshive

Page: 29 / 40

AVANT A36883 Operator'S Manual For Attachment Download Page 29

29 (40)

7.

Installing a side brush

The side brush can be fitted on either side of the broom. As standard, the side brush installation kit includes

the needed components to connect the water spraying system to the side brush.

7.1

Qualification requirements for installation work:

Knowledge and skills about hydraulic assemblies are required for making the installation. It is recommended

to leave the installation of hydraulic components to qualified service technicians. The manufacturer or it’s

representative are not responsible for damages, losses or injuries resulted from incorrect or incomplete

installations. Contact your nearest Avant dealer or service point, if you have any additional questions or

require installation services.

DANGER

Risk of high pressure fluid injection through skin.

Installation includes assembling

hydraulic components. Incorrect assembly or loose fittings may cause ejection of high
pressure fluid. Follow carefully all safety procedures regarding hydraulic assemblies and
all given instructions.

The instructions given in this chapter are intended for qualified service technicians or
individuals with training and experience about hydraulic assemblies.

WARNING

Risk of serious personal injury.

The safety procedures concerning hydraulic

assemblies apply both when installing new components or when modifying existing
hydraulic systems. The following installation instructions include the necessary
information needed in installation, but installation or modification work are allowed only if
the person doing them can perform them safely.

The following safety procedures and general safety principles regarding hydraulic
systems must be followed. Contact your Avant dealer or service point for more
information or installation services.

Protect the environment from leaking of hydraulic oil and prevent oil from draining on the
ground. Keep any loosened hydraulic hose in an upright position or plugged, so that they
will leak as little as possible.

Clean the equipment thoroughly before starting the installation and make sure that i.e.
dirt, dust or water will not enter the hydraulic components or the hydraulic oil. Keep the
protective covers in place until the components can be installed directly. Follow safety
procedures and wear proper personal protective equipment.

«
...
27
28
29
30
31
...
»

Summary of Contents for A36883









































Reviews:

No comments