AUX ASW-H09A4/SAR1DI, Service Manual

Page: 32 / 50

30
y the corresponding fault code.
or fan-motor will
utively within 10 s, if there is still no
the short circuit or the opening, it will
omplete machine will stop working. It will
exceeding the maximum rotational speed,
up abnormally, the G-TR short circuit, abnormal position
or
e
o
ditioner is not in normal communications in continuous 90s, it will show the
mpressor will stop after 30s.Until it is in normal
lly if
sensor models, the error was 2 ) after the
℃
operates for 5 min, the indoor fan will operate in weak wind
st be cut
.
en it stops working and displays the fault code.The
off and re-power in order to restart work.
ote control, emergency
r the
city must be cut off and re-power in order to restart
the compressor must have run for more than 5 min.
pass by full-wave rectifier, and
s voltage to control the speed of indoor fan .If such
The above protection will go on until Td ≤ 85 ,
℃
and it stops working more than 3 min, then the
compressor will resume normal operation;
When the compressor restart again, if Td reaches more than 110 again within 15 min, the
℃
compressor will stop immediately and displa
5
、
The malfunction protection of indoor fan-motor
If there is no signal after the indoor fan-motor starts working for 10 s, the indo
stop for 30 s. And this will test for three times consec
feedback signal (such as the fan is blocked or damaged, the wiring is disconnected , etc.),
then the digital tube will display the corresponding fault code, furthermore the complete
machine will stop working and can not be activated.
6
、
The malfunction protection of the sensor
When the indoor and outdoor temperature sensor has
display the corresponding fault code and the c
resume to work until the fault code vanishes.
7
、 Protection of IPDU module
When IPDU breaks down any of the following:
vibration from the position, speed
detection of loop , abnormal current sensor, locking of the compressor, damage of the
compressor, when the Case thermo moves, the compressor stops operating, and the outdo
unit will display the fault code while the indoor unit will show l the total fault code, and th
compressor will re-start again after 3 min. If such failures happen consecutively for two times
within 4 min, there will be permanent shutdown and the power must be cut off if you want t
re-activate.
8
、
Fault communication protection
If the air-con
corresponding fault code, then the co
communications and the fault code disappear, the air-conditioner will activate automatica
it meets the protection conditions for 3 min .
9
、
System Fault Protection
1. the cooling mode:
If it is measured Tr - Te <5 (for different
℃
compressor continuely
automatically. If still Tr - Te < 5
℃
8 min later, then the compressor stops and displays the fault code . The electricity mu
off and re-power in order to restart
2. the heating mode:
A) If Te <20 continues for 20 min, th
℃
electricity must be cut
We judge from system failures by this condition only within 20 min after we turn-on the
machine, 20 min later we no longer judge by this condition. If rem
switch is turned off or the electricity is cut off suddenly ,we re-judge system failure afte
air conditioner restart again within 20 min.
B) in the normal operation of the compressor, if Te <5 continues for 5 min, then it stops and
℃
display the corresponding code. The electri
work.
Judging from system failures in the following conditions :only 20 min after turn-on the machine
and also
10
、 Fault protection of zero detection
There will be small 100 Hz AC voltage when indoor AC voltage
the CPU will detect the zero point of thi
zero point can not detected for 400 ms, then it will display the fault code , the complete
machine will stop working and can not be started .