Autel EU908 Manual Download

Page: 96 / 100

Figure 11-15



The screen will display as below, which means the replaced battery is
being entered in the DDE/DME.

Figure 11-16



When the replaced battery has been successfully registered in the
engine electronics, press the

button to end the service function.



If the replaced battery has a different type from the original one, select

[3]

and press the

button to continue.



Refer to the steps described for registering the replaced battery with
higher/lower capacity.

Close-circuit Current

The close-circuit current should always be measured if increased current
consumption is suspected. Battery will discharge at a relatively fast rate even
current consumption rates slightly above the normal.

Close-circuit Current Monitoring Evaluation

1. Use the

UP/DOWN

scroll button to select

Close-circuit current

option

from the Power supply (Battery) menu and press the

button.

2. Select

Evaluate close-circuit current

monitoring option and press the

button to display the last 24 close-circuit current values.

Enter 6-digit supplier number as

described.

Finish Show Esc

000000

The battery replacement is being

entered in the engine electronics

(DDE or DME)

Please wait!

Summary of Contents for EU908





































































































Search results

Summary of Contents for EU908

Reviews:

Related manuals for EU908

Brands by name

Popular brands

Autel EU908, Manual

Search results

Summary of Contents for EU908

Reviews:

Related manuals for EU908

Brands by name

Popular brands