Aurora Design SCRF User And Technical Manual Download Page 33

Page: 33 / 33

Firmware Revision History

Revision 2.1, February 21, 2007:

1) Updated to support revision “B” image FLASH memories.

Revision 2.0, January 16, 2007:

1) Updated for revision 2.0 hardware.
2) Added externally adjustable RF channel select switch.
3) Added audio test tone in default mode.

Revision 1.8, August 26, 2006:

1) Updated 441/25i standard to match German specifications.
2) Added channels B1 and B2 to System E for Berlin transmitter.

Revision 1.7, June 18, 2006:

1) Increased internal fpga clock frequency to ease filter design.

Revision 1.6, June 12, 2006:

1) Added Sleep Disable feature to Option switch position 7.
2) Modified SCRF-819F and SCRF819L units for dual RF system capability.

Revision 1.5, May 18, 2006:

1) Increased accuracy of sine wave generator for internal test modes.
2) Added functionality to Test Mode 2 to measure SNR of D/A.

Revision 1.4, May 8, 2006:

1) Improved the high frequency video response of the unit.

Revision 1.3, May 3, 2006:

1) Improved timing to image FLASH.
2) Added a sixth test mode to aid in modulation depth measurements.

Revision 1.0, April 6, 2006:

1) Initial release.

Note:

Hardware/Firmware revision level can be found on bottom label of unit.

Firmware Revision History

Summary of Contents for SCRF

































Search results

Summary of Contents for SCRF

Reviews:

Brands by name

Popular brands

Aurora Design SCRF, User And Technical Manual

Search results

Summary of Contents for SCRF

Reviews:

Brands by name

Popular brands