Aurora Design SCRF User And Technical Manual Download Page 32

Page: 32 / 33

Available Models

Model No. SCRF-343M

NTSC to 343/30i with all System M (1937) and System M (1934) channels

Model No. SCRF-343A

NTSC to 343/30i with all System A channels

(1)

Model No. SCRF-441NM

NTSC to 441/30i with all System M (1946) and System M (1940) channels

Model No. SCRF-525M-SC

NTSC to 525/30i sequential color with all System M (FM audio) channels

Model No. SCRF-405A-NTSC

PAL/SECAM to 405/25i NTSC Color with all System A channels

Model No. SCRF-405A

PAL/SECAM to 405/25i with all System A channels

Model No. SCRF-441PE

PAL/SECAM to 441/25i with System E channel 1 and B1/B2

Model No. SCRF-455E

PAL/SECAM to 455/25i with System E channel 1

Model No. SCRF-819E

PAL/SECAM to 819/25i with all System E channels

(2)

Model No. SCRF-819F

PAL/SECAM to 819/25i with all System F and System E

(2)

channels

Notes

(1) This unit is useful for operating 405/25i televisions in parts of the world that use

NTSC video and 60Hz AC power. By adjusting the vertical (frame) oscillator in
the television, NTSC video can be used to operate these televisions.

(2) The System E channels for the SCRF819E model are full video bandwidth. The

System E channels for the SCRF819F and SCRF819L models are reduced
bandwidth.

Supported RF Systems

Summary of Contents for SCRF

































Search results

Summary of Contents for SCRF

Reviews:

Brands by name

Popular brands

Aurora Design SCRF, User And Technical Manual

Search results

Summary of Contents for SCRF

Reviews:

Brands by name

Popular brands