manualshive.com logo in svg

Aurora Design SCRF, User And Technical Manual

Share
Download
Aurora Design SCRF User And Technical Manual Download Page 20

Mode 6:

In this mode, a video test pattern consisting of a multi-burst will be
output from the unit on both the composite output and RF output.
This test can be used to align a television set for frequqncy reponse.
There are 7 bands of assending frequency, each ratiometrically
derrived from the Interpolator clock frequency listed in the Support
Conversions section. The seven ratios are as follows: 1/48, 1/36,
1/24, 1/18, 1/12, 1/9 and 1/6,

Mode 7: 

This mode selects normal operation

.

 This can be used to verify

adjustments made in the prior modes on actual input video and
audio without having to leave the 

Setup and Test Mode.

Updating Firmware

If it ever becomes necessary to update the firmware in the unit, this can be 

accomplished through the programming port next to the Option Switch as previously 
shown. The connector is a standard 8 pin, double row, 2mm connector. A custom 
cable with a mating connector is used in conjunction with a Xilinx Parallel III or 
Parallel IV download cable and the appropriate software. A full description of the 
hardware, software, and procedure to FLASH the unit can be found in the 
supplemental programming guide for the converter.

Introduction                                                                                                               

20

Summary of Contents for SCRF


































Reviews:

No comments

Brands by name

Popular brands

Load more brands