manualshive.com logo in svg

AUMA Aumatic AC 01.1, Manual, Page: 61 / 96

Share
Download
AUMA Aumatic AC 01.1 Manual Download Page 61

7.9.2 Feedback signals on the display

The following indications are displayed in status indications

S0

and

S3

:

È

Description of the displays:

EMERGENCY STOP/EMCY STOP ACTIVE

The EMERGENCY STOP button has been operated and has put the
AUMATIC into the EMERGENCY STOP status. This status can only be
cancelled by unlocking the EMERGENCY STOP button and issuing a sub-
sequent RESET command.

7.9.3 Feedback signals setting via output contacts

Æ

Via the menu to parameter:

MAIN MENU (M0)

SETTINGS (M1)

I/O 1 (M14)

OUTPUT CONTACT 1 - 5

È

Description of the parameter settings:

EMCY STOP BUTTON

The selected output contact is activated, after the EMERGENCY STOP
button was operated.
This signal can be cancelled by unlocking the EMERGENCY STOP button.

7.9.4 Feedback signal setting via LEDs

Æ

Via the menu to parameter:

MAIN MENU (M0)

SETTINGS (M1)

LOCAL CONTROLS (M13)

LED 1 - 4

È

Description of the parameter settings:

EMCY STOP BUTTON

The selected LED is illuminated after the EMERGENCY STOP button was
operated.
This signal can be cancelled by unlocking the EMERGENCY STOP button.

61

Actuator controls

Manual

AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus



‚

NOT READY IND.

S3

EMCY STOP ACTIVE

EDIT

M1412

OUTPUT CONTACT 1

EMCY STOP BUTTON



‚

:EDIT

↵

:OK

C:ESC

EDIT

M1313

LED 2

EMCY STOP BUTTON



‚

:EDIT

↵

:OK

C:ESC

Ü

É

EMERGENCY STOP

S0

Summary of Contents for Aumatic AC 01.1

































































































Reviews:

No comments