AUMA Aumatic AC 01.1 Manual Download Page 14

Page: 14 / 96

3.6

Language change in the display

Via the menu to parameter:

MAIN MENU (M0)

LANGUAGE/CONTRAS (M00)

LANGUAGE (M010)

Default value:

GERMAN

Setting range:

GERMAN, PORTUGUESE, ITALIAN, SPANISH,
FRENCH, ENGLISH, TUERKCE, POLSKI, MAGYAR

3.7

LCD contrast setting of the display (applies only to controls with green display)

To improve the legibility of the display under unfavourable lighting condi-
tions, the contrast may be adjusted.
This setting is only possible for green displays. The contrast setting has no
effect on the blue display.

Via the menu to parameter:

MAIN MENU (M0)

LANGUAGE/CONTRAST M00)

LCD CONTRAST (M011)

Default value:

80 %

Setting range:

0 %

100 %

Information

Alternatively, the LCD contrast can be set as follows:
1. Press

and hold it down.

The menus

are skipped.

After approximately 10 seconds, the LED display will continuously
change from bright to dark and vice versa.

2. Release push button

The current brightness level is saved.

Actuator controls
AUMATIC AC 01.1/ACExC 01.1 Foundation Fieldbus

Manual

EDIT

M010

GERMAN

ENGLISH

:EDIT

↵

:OK

C:ESC

EDIT

M011

LCD CONTRAST

30 %

:EDIT

↵

:OK

C:ESC

Summary of Contents for Aumatic AC 01.1

































































































Search results

Summary of Contents for Aumatic AC 01.1

Reviews:

AUMA Aumatic AC 01.1, Manual, Page: 14 / 96

Search results

Summary of Contents for Aumatic AC 01.1

Reviews: