Aulisa Guardian Angel Rx GA2000 Instructions For Use Manual Download Page 64

The FCC requires the user to be notified that any changes or 
modifications to this device that are not expressly approved by Taiwan 
Aulisa Medical Devices Technologies, Inc. may void the user's 
authority to operate the equipment.

For Display Unit & Receiver/Transponder

Declaration of Conformity with FCC for Electromagnetic Compatibility

This device complies with Part 15 of the FCC Rules. Operation is subject 
to the following two conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.

Federal Communications Commission (FCC) Notice

This equipment has been tested and found to comply with the limits for a 
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area is 
likely to cause harmful interference in which case the user will be 
required to correct the interference at his own expense.

FCC Radiation Exposure Statement

For Display Unit

This equipment is compliance with SAR for general population/uncontrolled 
exposure limits in ANSI/IEEE C95.1-1999 and had been tested in 
accordance with the measurement methods and procedures specified 
in OET Bulletin 65 Supplement C. The highest reported SAR for the 
device is 0.116 W/kg.

For Receiver/Transponder

This equipment complies with FCC radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body. This 
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

61

Summary of Contents for Guardian Angel Rx GA2000
















































































Reviews: