Auerswald COMmander Basic.2, Installation And Commissioning Instructions

Page: 11 / 84

Important Information
11
Important: To support the COMmander 8VoIP
module and the COMmander 16VoIP module, the
PBX requires firmware version 3.0.
Important: To support the VMF module, the PBX
requires firmware version 4.0.
Important: Due to technical reasons, when inserting
the first VoIP module, both VoIP channels on the
base device must be switched off.
Important: If a non-compatible COMmander 4S
0
module is damaged by its short circuit when being
operated in a COMmander Basic.2, repair charges
are required.
씮
Use only COMmander 4S
0
modules labeled as
version “Rev. 2” or “Rev. 3”.
씮
It may be possible to retrofit other existing
modules that do not have this label. For more
information about this, please contact our
technical Hotline.
Note: The first series of the COMmander 4S
0
module
was designed for the power supply of the
COMmander Basic regarding short-circuit resistance.
Due to be significantly larger power supply unit for the
COMmander Basic.2, the module needed to be
adapted in order to ensure continued short-circuit
resistance.
Note: Switching between the internal and external
operating modes of the S
0
ports is done using
jumpers on the S
0
modules.
Note: Using the configuration manager, any number
of available VoIP channels can be reserved for
internal and external calls.
Software Extensions
When the PBX is enabled in an Upgrade Centre, various
extensions and other features can be activated .
Important: The system dongle required for the
extension is not part of the basic unit.
You can extend the PBX with the following functions:
Hotel Function
Automatic reception
Project numbers
X.31 on an internal S
0
port
The following functions, some of which are already
enabled, can be extended:
LCR (number of subscribers from 16 to 112)
LAN-TAPI (number of subscribers from 4 to 112)
Call data recording (number of data sets from 3000
to 9000)
Call Through (number of available lines from 4 to
all)
In addition, the following phone numbers/channels and
the number of voice mail/fax boxes can be extended:
Subscriber numbers (number of subscribers from
48 to 112)
VoIP channels (an additional 8)
Voice mail/fax boxes (an additional 40, each)
Important: The addition of the boxes and voice mail/
fax channels requires that a COMmander VMF
module is present.
The addition of eight VoIP channels requires that at
least one COMmander 8VoIP module is present and
the maximum number of VoIP channels has not yet
been reached.
Maximum Extension
The PBX can be operated with a maximum of 48 internal
subscriber connections (analog, VoIP, and ISDN).
Note: One internal S
0
port corresponds to two inter-
nal subscriber connections in this case. This means
that the limit is reached with e.g. 16 internal S
0
ports,
8 U
P0
ports, and 8 a/b ports.
Note: An S
0
or U
P0
port set to the option free in the
port configuration under Application is not consid-
ered in the calculation of this limit.
The PBX can be operated with a maximum of 34 trunk
lines (consisting of external VoIP and ISDN channels).
The maximum number of individual ports/channels each
is indicated in the following table:
Note: An S
0
port corresponds to two ISDN channels;
an S
2M
port corresponds to 30 ISDN channels.
The maximum number of individual modules each is
indicated in the following table:
Note: If two COMmander 16VoIP modules are
inserted, the number of VoIP channels available is
automatically limited to 24.
Ports/channels Max. number
External S
2M
ports 1
External S
0
ports 8
External S
0
ports (for the available S
2M
port) 2
Internal S
0
ports 24
Internal U
P0
ports 32
Internal analogue ports 32
VoIP channels (internal and external) 24
Voice mail/fax channels 8
Module Max. number
COMmander S
2M
module 1
COMmander 4S
0
module (rev. 2 and 3) 5
COMmander 8S
0
module 3
COMmander 8U
P0
module 4
COMmander 8a/b module 4
COMmander 2TSM module 1
COMmander 8VoIP module 2
COMmander 16VoIP module 1
COMmander VMF module 1