background image

 
 
 
 

 
 

 
 

 

 

 

 

 

 

 

 
 
 

 
 

 

 

 

 

 
 

 

 

 

 

 

 

 
 

 

 

 

 

 
 

 
 
 

 
 
 
 
 
 
 
 
 

 
 
 

! IMPORTANT SAFETY INFORMATION !

 

RISK  OF  SHOCK  OR  ELECTROCUTION!  INTERNAL  OPERATING 
VOLTAGES ARE LETHAL! 
 

Do not remove top cover, unless specifically instructed to do so in the user 
manual. 
 
This unit contains fuses and other safety components in accordance with 
BS60065 requirements. 
In  the  event  of  failure,  replacement  fuse  or  safety  component  must  be  of 
the same part type and value. 

 

This product generates high levels of heat. Adequate ventilation must 
be  provided.  Do  not  restrict  airflow  through  any  ventilation  slots  or 
place the unit on any surface that may restrict airflow. 
 
Valve equipment operates at extremely high temperatures;  

KEEP OUT OF THE REACH OF CHILDREN AND ANIMALS.

 

Do  not  store  or  operate  this  unit  in  areas  of  high  humidity  or  in  close 
proximity to water / moisture. 

 

Do not expose or immerse the unit in liquid of any kind. 
 

 

This product must be earthed – ensure that the mains supply cable earth / 
ground is correctly connected. 
 
 

 

OTHER SAFETY PRECAUTIONS: - 

 

Never touch the power cord with wet hands. 

 

Always remove the power cord by grasping the plug, not the cable. 

 

Never expose the unit to excessive heat or magnetism. 

 

Never let an inexperienced person repair or reassemble the unit. 

 

Never put anything, especially metal objects, inside the unit. 

 

Never place excessive weight on the unit. 

 

SUCH REPLACEMENT MUST ONLY BE CARRIED OUT BY A 
QUALIFIED SERVICE TECHNICIAN. 

 

Do not attempt to replace any fuses without first disconnecting the unit from 
the mains electricity supply.

 

Summary of Contents for TT-Three






























Reviews: