Atwood SCALE-O-MATIC S302, Operation And Safety Manual

Page: 9 / 53

AM MFG. CO. MASTER MODEL:
DIV. OF ATWOOD CORP. S302
© 2011
S302_7 7 1/11
OPERATING INSTRUCTIONS
I. PRELIMINARY START-UP PROCEDURE
A. REMOVE PACKING, PACKING SLIPS, DOCUMENTS AND OTHER OBSTRUCTIONS FROM HOPPER.
B.
MAKE SURE MACHINE IS ON A FLAT SURFACE
C. MOVE MACHINE INTO POSITION & LOCK CASTERS.
D. PLUG POWER CORD INTO PROPER RECEPTACLE. / PROPER GROUNDING IS
NECESSARY TO PREVENT ANY TYPE OF ELECTROSTATIC PHENOMENA.
E. PUSH DIVIDER START BUTTON.
F. CHECK ROTATION OF DIVIDER BY LOOKING THROUGH SMALL INSPECTION DOOR. LARGE GEAR SHOULD BE
TURNING (C.W.) CLOCK-WISE.
G. IF THE GEAR IS TURNING IN THE (C.C.W.) COUNTER- CLOCK WISE DIRECTION, CONSULT A PROPERLY TRAINED
ELECTRICIAN.
H. IF ROTATION IS CORRECT, YOU ARE READY TO CONTINUE ON WITH THESE PROCEDURES.
I. CHECK POWER SUPPLY TO ROUNDER AND DISCHARGE CONVEYOR BY PRESSING THE START BUTTON LABELED
“CONVEYOR / ROUNDER” ON THE CONTROL PANEL. THE ROUNDING DRUM SHOULD BE TURNING IN A (C.C.W.)
ROTATION, AND THE DISCHARGE CONVEYOR SHOULD BE RUNNING FORWARD, OUT FROM MACHINE.
II.OPERATION OF DIVIDER
A. FILL THE OIL RESERVOIR WITH LIGHTWEIGHT MINERAL OIL. BE SURE TO CLEAN ANY OIL SPILL AROUND MACHINE.
THESE SURFACES BECOME SLIPPERY.
B. WITH THE SQUIRT BOTTLE SUPPLIED, APPLY A SMALL AMOUNT OF MINERAL OIL TO THE INSIDE SIDES OF THE
DOUGH HOPPER. (HOPPER SHOULD BE OILED EVERY TIME YOU PLACE NEW DOUGH IN IT.)
C. OPEN THE VALVE LOCATED ON THE TOP GIB BAR APPROXIMATELY 1/8 OF A TURN.
D. REMOVE BACK CABINET DOOR.
E. OPEN THE CYLINDER VALVE APPROXIMATELY 1/8 OF A TURN. THIS VALVE IS LOCATED ON THE OIL PUMP BEHIND
THE REAR DOOR.
F. REINSTALL THE BACK CABINET DOOR.
G. FILL THE HOPPER WITH DOUGH. BY LOADING DOUGH @ 20 lbs. PIECES. DO NOT LIFT MORE THAN 20 lbs. PIECES.
THIS COULD CAUSE SERIOUS LOWER BACK INJURY.
H. CLOSE HOPPER COVER AND PULL SPRING PIN AND SET HOPPER PADDLE ON TOP OF DOUGH
I. PRESS THE “CONVEYOR / ROUNDER” START BUTTON
J. PRESS DIVIDER BUTTON
.
III. DIVIDING THE DOUGH
A. DOUGH IS PORTIONED IN THE CUP LOCATED ON THE DIVIDER SLIDE.
B. TO ADJUST THE WEIGHT, STOP MACHINE.
C. BY TURNING THE HANDLE IN A COUNTER CLOCKWISE MOTION, THE DOUGH WEIGHT WILL INCREASE. TURNING
THE HANDLE IN A CLOCKWISE MOTION DECREASES THE DOUGH WEIGHT.
D. FIND YOUR DESIRED DOUGH WEIGHT BY WEIGHING THE DOUGH PIECE.
E. ONCE YOU HAVE ACHIEVED THIS, ADJUST THE LOCKING STAR KNOB ( 529MS-2D ) TO THE TOP OF THE MEASURING
CUP TO KEEP SCALING ACCURATE.
CAUTION:
PISTON WILL MOVE AFTER POWER IS TURNED
OFF OR DISCONNECTED.
WARNING
:
UNIT MUST BE PROPERLY OPERATED AND MAINTAINED TO PREVENT MACHINE DAMAGE OR PERSONAL
INJURY. REVIEW INSTRUCTIONS WITH ALL EMPLOYEES BEFORE USE.
CAUTION:
BEFORE BEGINNING START - UP, READ ALL INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE LOCATIONS
OF ALL CONTROLS. KNOW HOW TO SHUT DOWN THE UNIT IMMEDIATELY IN CASE OF TROUBLE. MAKE CERTAIN
ALL PERSONNEL NOT INVOLVED IN THE START - UP ARE SAFELY AWAY FROM THE MACHINE BEFORE ANY
SYSTEMS ARE STARTED...